Woodward 505XT Скачать руководство пользователя страница 47

Страница: 47 / 242

Manual 35018V1

505XT Digital Control System for Steam Turbines

Woodward

Hardware - Relay Outputs

This control provides (8) Isolated, Form-C Relay outputs with NO, COM, NC contacts available at the
terminal block.

Features

•

(8) Relay Output Channels

•

Each Relay Output provides NO, COM, and NC contacts

•

Each Relay Output channel provides a coil voltage readback fault

•

Woodward GAP block, diagnostics, and configuration support

•

Contact isolation maintained at terminal blocks

•

ATEX approved version available using hermetically sealed relays

•

GAP configurable update rates of 5 ms to 160 ms

Table 2-12. Specifications (Relay Outputs)

Number of channels

(8) relays

Contact Type

Form-C with NO, COM, and NC terminals

STD Relay, contacts (DC)

5 A, 5-30 Vdc (resistive)

STD Relay, contacts (AC)

2 A, 115 Vac (resistive)

STD Relay, operate time

< 15 ms typical

RELAY Coil Readback

Coil voltage readback status is available

RELAY Coil Rdbk Filter

1 ms approx at room temp

RELAY Output Isolation

500 Vrms minimum to EARTH and all other I/O

RELAY Contact Isolation

500 Vrms minimum between open contacts

RELAY to RELAY Isolation

500 Vrms minimum between relays

IOLOCK State

Relay outputs are de-energized during power-up, power-
down, core voltage failures and watchdog failures

ATEX version:

The ATEX approved control uses a Hermetically sealed relay

ATX Relay, contacts (DC)

5 A, 5-30 Vdc (resistive), 0.2-0.5 A (inductive)

ATX Relay, contacts (AC)** 2 A, 115 Vac (resistive), 0.1-0.2 A (inductive)

Explosion

Hazard

**ATEX/IECEx Compliance requires relay contact loads be
limited to < 32 Vac rms / < 32 Vdc.

Figure 2-12. Relay Output Block Diagram

Содержание 505XT



















































































































































































































































Результаты поиска

Содержание 505XT

Отзывы:

Woodward 505XT, Инструкция по установке и эксплуатации, Страница: 47 / 242

Результаты поиска

Содержание 505XT

Отзывы: