manualshive.com logo in svg

Woodward 505XT, Инструкция по установке и эксплуатации, Страница: 148 / 242

Поделиться
Скачать
Woodward 505XT Скачать руководство пользователя страница 148

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

146 

CONTACT INPUT 01 
FUNCTION Emergency 

Stop 

 

This channel is a dedicated trip input. 

DEVICE TAG 
 

This is a user entered field. It allows entry of a short description or tag name for this channel. 

 

CONTACT INPUT xx 
FUNCTION 

(must choose from list) 

 

Scroll through the menu by navigating the focus highlighter to the desired item, pressing ENTER, 
using the Adjust Up/Down Arrows, and then pressing the ENTER key again to select the 
option/function. Press the ESC key to cancel the selection. 

CONTACT INPUT OPTIONS 
 

These 3 channels are defaulted as shown – but can be modified if desired. 

CONTACT INPUT 02 

dflt= Reset Command 

CONTACT INPUT 03 

dflt= Speed Raise Command 

CONTACT INPUT 04 

dflt= Speed Lower Command 

 
 

See tables in chapter 1 for the list of functional options: 

 

 

Many of the functions in this list are described in other sections of the manual containing the functional 
description. Functions that are not described elsewhere in the manual or need clarification are described 
as follows: 
 
Instant Minimum Governor – This feature will quickly ramp the speed setpoint to the configured Minimum 
Governor setpoint, if configured as a mechanical drive application, or to the Minimum Load Setpoint if 
configured as a generator application. 
 

DEVICE TAG 
 

This is a user entered field. It allows entry of a short description or tag name for this channel. 

INVERT LOGIC? 

dflt= NO (Yes/No) 

 

Select this to invert this contact input. Inverting means that a function normally activated when 
CLOSED or TRUE will not be activated when the contact is OPEN or FALSE.  Note that this is not 
required for External Trip inputs because the “Normal” or “Non-Inverted” functionality is already fail-
safe (CLOSED/TRUE = healthy, OPEN/FALSE = trip). 

 
Contact Inputs # 3 through # 20 are entered following the same rules as described for Contact Input # 2. 
 

Relays Menu 

 
You may configure up to seven relays in addition to the one pre-assigned relay (Shutdown). Each relay 
can be configured as either a level switch or as an indication. An example of a level switch is a Speed 
Switch and an example of an indication is Cascade Control Enabled. 
 

RELAY OUTPUT 01 
RELAY OUTPUT FUNCTION 

Trip Relay 

 

This channel is a dedicated trip output.

 

DEVICE TAG 
 

This is a user entered field. It allows entry of a short description or tag name for this channel. 

 
RELAY OUTPUT 02 
USE AS LEVEL SWITCH? 

dflt= NO (Yes/No) 

 

Select this to use this relay output as a level switch. Otherwise, the relay output will be a status 
indication. 

RELAY OUTPUT FUNCTION 

(must choose from list) 

 

Scroll through the menu by navigating the focus highlighter to the desired item, pressing ENTER, 
using the Adjust Up/Down Arrows, and then pressing the ENTER key again to select the 
option/function. Press the ESC key to cancel the selection. 

 

Содержание 505XT



















































































































































































































































Отзывы:

Нет отзывов