manualshive.com logo in svg

Woodward 505XT, Инструкция по установке и эксплуатации, Страница: 157 / 242

Поделиться
Скачать
Woodward 505XT Скачать руководство пользователя страница 157

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

155 

Event 
ID 

Description Error 

Meaning 

99 

Maximum Speed > 
Probe 1 Freq Range 

The maximum speed input is 35000 hertz. This is a limitation of 
the 505’s hardware/speed sensing circuitry. The frequency input of 
the speed sensor must be less than this value. The gear the 
speed sensor is mounted on may need to be changed to one with 
less teeth, this will decrease the frequency seen by the speed 
probes. The Maximum Speed Level for Speed Input Channel 1, 
converted to frequency (Hz), is greater than 35000 Hz. 

100 

Maximum Speed > 
Probe 2 Freq Range 

The maximum speed input is 35000 hertz. This is a limitation of 
the 505’s hardware/speed sensing circuitry. The frequency input of 
the speed sensor must be less than this value. The gear the 
speed sensor is mounted on may need to be changed to one with 
less teeth, this will decrease the frequency seen by the speed 
probes. The Maximum Speed Level for Speed Input Channel 2, 
converted to frequency (Hz), is greater than 35000 Hz. 

101 

Speed Sensor #1 Failed 
< Freq Range 

The failed speed setting for speed input #1 is below the minimum 
allowed setting. The minimum allowed setting is calculated as 
follows: (Maximum Speed Level) * (0.0204). 

102 

Speed Sensor #2 Failed 
< Freq Range 

The failed speed setting for speed input #2 is below the minimum 
allowed setting. The minimum allowed setting is calculated as 
follows: (Maximum Speed Level) * (0.0204). 

103 

No Start Mode 
Configured 

No start mode is selected in the Configure mode. One of the three 
start modes must be selected in the Configure mode under the 
Start menu. 

104 

Remote KW Setpoint 
Configured, No AI 

The Remote kW Setpoint is configured as used but no analog 
input is configured as a Remote kW Setpoint. 

105 

Remote Speed and KW 
Setpoint 

Both Remote Speed Setpoint and Remote kW Setpoints are 
configured as used. Only one of these inputs may be configured. 

106 

Hot Start greater than 
Cold Start 

The time configured for a Hot Start is greater than the Cold Start. 
The time remaining after shutdown for a Hot Start must be less 
than the time for a Cold Start. 

107 

Hot Reset Timer Level 
Error 

Hot Reset Timer Level is greater than the Maximum Governor 
speed level or less than the Minimum Governor speed level. The 
Hot Reset Timer Level must be between Minimum and Maximum 
Governor. 

108 

Temperature 1 or 2 
used, no AI 

A Start Temperature function is configured but no Analog Input is 
configured as a temperature input. 

109 

Cascade Speed Limit 
Error 

The Cascade minimum speed limit is configured less than 
Minimum Governor, the Cascade maximum speed limit is 
configured greater than Maximum Governor, or the Cascade 
minimum speed limit is greater than the Cascade maximum speed 
limit. 

110 

KW Signal Source Not 
Selected 

A controller has been configured to use a kW input but no Primary 
or Secondary Signal source has been selected under Operating 
Parameters. 

111 

SYNC Signal Source Not 
Selected 

A controller has been configured to use a Synchronization input 
but no Primary or Secondary Signal source has been selected 
under Operating Parameters. 

Содержание 505XT



















































































































































































































































Отзывы:

Нет отзывов