manualshive.com logo in svg

Woodward 505XT, Инструкция по установке и эксплуатации, Страница: 156 / 242

Поделиться
Скачать
Woodward 505XT Скачать руководство пользователя страница 156

Manual 35018V1 

505XT Digital Control System for Steam Turbines 

 

 

 

Woodward 

154 

Event 
ID 

Description Error 

Meaning 

81 

Idle 2 Setpoint > 
Minimum Governor 

The Idle Speed setpoint is configured at a higher speed than the 
minimum governor speed setpoint. 

82 

Idle 3 Setpoint > 
Minimum Governor 

The Idle Speed setpoint is configured at a higher speed than the 
minimum governor speed setpoint. 

83 

Idle 1 > Idle 2 

The Idle 1 speed setpoint is configured at a higher speed than the 
Idle 2 speed setpoint. 

84 

Idle 2 > Idle 3 

The Idle 2 speed setpoint is configured at a higher speed than the 
Idle 3 speed setpoint. 

85 

Rate to Idle 2 Error 

The Cold Rate to Idle 2 (rpm/second) is configured at a higher rate 
than the Hot Rate to Idle 2. Or the Warm Rate to Idle 2 (if used) is 
configured at a higher rate than the Hot Rate to Idle 2. 

86 

Rate to Idle 3 Error 

The Cold Rate to Idle 3 (rpm/second) is configured at a higher rate 
than the Hot Rate to Idle 3. Or the Warm Rate to Idle 3 (if used) is 
configured at a higher rate than the Hot Rate to Idle 3. 

87 

Rate to Rated Error 

The Cold Rate to Rated (rpm/second) is configured at a higher 
rate than the Hot Rate to Rated. Or the Warm Rate to Rated (if 
used) is configured at a higher rate than the Hot Rate to Rated. 

88 

Critical Band Rate < 
Slow Rate 

The acceleration rate (rpm/second) through the critical speed 
avoidance band must be faster than the normal speed set point 
rate. 

89 

Critical Speeds Enabled, 
No Idle 

A critical speed avoidance band is configured but neither idle/rated 
nor auto start sequence is configured. To use the critical speed 
avoidance logic one of these functions that uses an idle speed 
must be programmed. 

90 

Critical Band Below 1st 
Idle Setpoint 

A critical speed avoidance band is configured below either the Idle 
speed set point (when using Idle/Rated) or the Idle 1 set point 
(when using the Automatic Start sequence). 

91 

Critical Band > Minimum 
Governor 

A critical speed avoidance band is configured higher than the 
Minimum Governor speed level. 

92 

Critical Band Min > Max 

A critical speed avoidance band minimum limit is configured 
higher than the maximum limit of that band. 

93 

Minimum Governor > 
Maximum Governor 

The Minimum Governor speed level is configured higher than the 
Maximum Governor speed level. 

94 

Rated Speed < Min Gov 

The Rated speed set point is configured at a lower speed than the 
Minimum Governor speed set point. 

95 

Rated Speed > Max Gov  The Rated speed set point is configured at a higher speed than 

the Maximum Governor speed set point. 

96 

Max Gov > Overspeed 
Test Limit 

The Maximum Governor speed level is configured greater than the 
Overspeed Test Limit. 

97 

Overspeed Trip > 
Overspeed Test SP 

The Overspeed Trip setpoint is greater than the Overspeed Test 
Limit. 

98 

Overspeed Test Limit > 
Maximum Speed 

The Overspeed Test Limit is configured greater than the Maximum 
Speed Level for speed input 1 or 2 (if used). 

Содержание 505XT



















































































































































































































































Отзывы:

Нет отзывов