background image

79

STAGE ONE:

 

CLEANING

PROBLEM 1:  

I CAN'T REMOVE THE VESSEL LID

Solution: 

Sometimes the vessel lid can be difficult to remove if the 

threads become bound together too tightly. In this case all  

that is needed is a little extra muscle from another person.  

So get help to unwind the lid counter-clockwise and you'll  

find the extra torque will allow the lid to be removed easily.

STAGE THREE:

  

DURING FERMENTATION

PROBLEM 1:  

THE YEAST DOESN’T SEEM TO START FERMENTING

Solution: 

Dried ale yeast should take ½ a day to show signs of fermenting 

and lager yeast about 1 day. If it takes longer than this then 

wait one more day for signs of activity. If by Day 2 there is no 

activity then it could be possible that the yeast had somehow 

died before use. If the yeast was rehydrated in water over 35°C 

(95°F) it may have been too hot. In general the dried brewing 

yeast WilliamsWarn uses is quite stable and should ferment 

even past its use by date unless the sachet has been broken and 

oxygen ingress has occurred or if it has been stored in very warm 

temperatures. 

In the case of no activity after 2 days, close the vessel valve, 

remove the sediment bottle, dump the non-fermenting yeast 

which will likely be sedimented at the bottom and then 

rehydrate a new quality yeast in 25°C water (77°F) for 10 

minutes. Add the sediment bottle back onto the brewery 

with the new quality yeast and open the valve in 2 stages, as 

described in the instructions (to avoid temperature shock). 

Monitor closely. 

PROBLEM 2:  

THE PRESSURE ISN’T BUILDING UP 

Solutions: 

1.  Check that there is activity in the sediment bottle and  

foam seen on the beverage surface through the sight-glass 

and that the vessel valve is open. If fermentation is only  

just starting, the amount of carbon dioxide being generated  

is small and the pressure will take a while to build up.  

If fermentation is vigorous and the pressure is not building 

up over a few hours under such fermentation conditions, 

then you probably have a leak. Ale yeast should take ¾ of  

a day to start to build up pressure and lager yeast about  

1 day. Firstly, release any pressure in the vessel via the 

VPRV by pressing the VPRV release button and remove the 

lid. Check the seal is sitting in the groove properly. It may 

need a stretch as explained in Appendix 4. Ensure the seal 

sits in the groove as shown in the photos in Appendix 4 and 

then re-close the lid tightly. Then monitor pressure build up.  

To speed up this test, you can manually add CO

from your 

gas cylinder and pressurise the tank to 1 bar. Firstly, wind 

the VPRV down to its fully closed position (clockwise). Then 

open the 3-way valve. Close the 3-way valve when the tank 

is at 1 bar and watch for a pressure drop. If the seal is in 

place properly and the lid is closed, the pressure should 

hold. Once the seal is confirmed, you can leave the pressure 

in the vessel, but re-set the VPRV to your chosen set-point 

e.g. 2½ turns open (anti-clockwise).

2.  It is possible the VPRV could be leaking. Obtain a children’s 

party balloon and place over the VPRV. If the balloon 

expands, the VPRV is leaking and needs attention. Release 

gas from the VPRV by pressing the VPRV release button and 

then unwind the VPRV fully. Examine the seal and spring for 

faults or obstructions or grit and clean. Examine the VPRV 

cavity for any obstructions or grit and remove if need be. 

Replace the VPRV with the seal and spring in their correct 

positions and monitor the pressure. If pressure still doesn’t 

build up, call the local help desk. 

PROBLEM 3:  

I CAN’T QUITE GET THE PRESSURE RIGHT WITH THE VPRV.

Solutions:

1.   You have a few days to get the pressure right during the 

first days of fermentation. Set an excess pressure on the 

VPRV, let the pressure in the vessel build up and then turn 

the VPRV counter-clockwise to release pressure until your 

set-point is reached and no more pressure is emitted at that 

setting. Check gas is released out the VPRV as the pressure 

goes past your desired set-point and then leave the VPRV 

set at that mark. 

2.  Just ferment at a pressure higher than your target. The yeast 

should ferment all the way even at high pressures and you 

can release excess pressure later. 

STAGE FOUR:  

COOLING

PROBLEM 1:  

THE COOLING DOESN’T SEEM TO WORK. 

Solutions:

1.  Check you have the brewery turned on. If not, turn it on. 

2.  Check you have set the correct temperature and that it is 

lower than the ambient temperature. If not, set the correct 

temperature. 

3.  Check the yellow refrigeration light is lit up on the tem-

perature controller LED readout. This should read SUB2. 

If the set-point is more than 1°C lower than the actual 

temperature this text should be lit up on the controller 

screen. If it is lit up and the temperature is not falling, there 

may be an issue with the compressor or a small pump that 

circulates the glycol. Call the local help desk. 

Содержание BrewMaster

















































































Отзывы: