WILLIAMSWARN BrewMaster Скачать руководство пользователя страница 13

Страница: 13 / 80

3. Check the draft tap is closed and the flow control lever on

the side of the tap is pushed all the way up to its closed

position. The draft tap should be automatically closed by

its spring, which is its central sitting position (Not sitting

forward and not sitting back).

4. Turn the 3-way valve clock-wise to the vessel pressure gauge

arrow and once the vessel low pressure gauge reaches

0.25 bar turn the 3-way valve back to the X position. The

pressure in the tank will drop down once you close the

3-way, and you will need to open and close the 3-way a

few times to get a final steady reading of 0.25 bar with the

3-way valve closed. If the beer and CO

lines have been

correctly installed then the system should then hold this

pressure. If the gauge drops immediately then it is possible

that one of the connections is not pushed in correctly. This

will need to be checked by firstly following the ACCESS TO
MACHINE INTERNAL PARTS AND SERVICING

for your safety

and then removing the rear protective panel again. Re-check

the connections and make sure they are locked in to the

push-lock fittings as described above.

CONNECT TO ELECTRICAL MAINS

Connect the electrical cord supplied into your brewery and

then plug in your unit to a standard 230V 50-60Hz AC mains

and press the green on/off button on the front of the unit. This

will start up the glycol pump and the unit will start heating or

cooling. Check to see that the vessel temperature (the larger

number) on the digital display is similar to the ambient room

temperature and then set the controller temperature (the smaller

number on the digital display) to 2

C using the temperature

adjustment buttons as shown in Figure 66 in Appendix 6. This

will turn on the refrigeration compressor and will start cooling

the cone portion of the vessel. A small yellow indicator will

appear on the display and read, SUB2. Within minutes you

should be able to check this as the vessel temperature, as read

on the display, will start dropping towards the set-point.

To check the heating, press the temperature adjustment buttons

to increase the temperature set-point to 5

C above the actual

vessel temperature. This will engage the heating element and a

small yellow indicator will appear on the digital screen and read

OUT 1. Within minutes the vessel temperature on the digital

display will start rising towards the set-point.

The brewery is now set-up and ready for brewing.

Press the green on/off button and turn the brewery off.

GENERAL AREA CLEANLINESS

It is optimal to maintain a clean area around the brewery. It is

natural and expected that you will spill beverage around the unit

as time goes by. Maintain a clean area around the brewery and

wipe drips from the surface of the brewery as much as possible.

Bacteria will start to grow on spilt beverage and it is always best

to reduce any risk of infection in your beverages by keeping a

tidy and dry brewing area.

IMPORTANT: AVOIDING A MAJOR SPILL

During fermentation, the pressure will build up in the vessel.

This is how the beverage becomes carbonated. There is a risk

of a major spill if the draft tap is open and the flow control lever

is open after the ingredients are added and fermentation is

started. In this situation as the pressure builds up just a little,

most of the 23 Litres (5 Imp. gal/ 6 US gal) of beverage will

pour out the tap and onto the floor.

As described clearly in the Instructions, when you are brewing

or when you have finished pouring beverage, you must ensure

the draft tap is in its closed position. When pulled forward, the

tap is open and when pushed back it is also open (the foam

mechanism) so it must sit in its neutral position to be closed.

A new tap should always spring back to its closed position, but

a tap that is not cleaned adequately can start to build up sticky

grime and may stick out from its closed position. Children or

guests can also open the draft tap by accident.

In any case, to avoid a major spill, unless you are pouring

beverages as intended, the flow control lever on the side of

the draft tap

MUST BE PUSHED UP ALL THE WAY TO ITS

FULLY CLOSED POSITION

in order to ensure that there will be

no leaking out of the draft tap, even if it is somehow not fully

closed. In addition, it is important to check the draft tap itself

is also in its closed position. In this way the tap is closed by two

means and the risk of a major spill is reduced.

Fig. 4C

1.   HIGH PRESSURE GAUGE
2.  SAFETY VALVE
3.  LOW PRESSURE GAUGE
4.   REGULATOR KNOB

5. LOW PRESSURE GAS
CONNECTION
6. GAS CYLINDER VALVE

Содержание BrewMaster

















































































Результаты поиска

Содержание BrewMaster

Отзывы:

Похожие инструкции для BrewMaster

Бренды по названию

Популярные бренды

WILLIAMSWARN BrewMaster, Руководство пользователя

Результаты поиска

Содержание BrewMaster

Отзывы:

Похожие инструкции для BrewMaster

Бренды по названию

Популярные бренды