WILLIAMSWARN BrewMaster Скачать руководство пользователя страница 80

Страница: 80 / 80

STAGE FIVE:

CLARIFICATION

PROBLEM 1:

I CAN’T MIX THE CLARIFICATION AGENT INTO THE

BEVERAGE

Solution:

Read Appendix 8 carefully for principles regarding clarification.

Ensure that the gas cylinder pressure is 0.5 bar (7 psi) higher

than the vessel pressure. Then ensure there is clarification agent

inside the clarification pot. Then turn the 3-way valve to the

pot and listen for the sound of mixing. If there is still no mixing

either increase the pressure from the gas bottle or decrease the

pressure in the vessel until mixing is heard. It could be one of

the gauges is reading incorrectly.

Other causes could be a blocked one-way valve under the pot

inside the tower or a blocked beer line (if hops or malt has been

added and particles are blocking the lines). Call the local help

desk for advice.

PROBLEM 2:

THE BEVERAGE IS NOT 100% CRYSTAL CLEAR AFTER 2

CLARIFICATIONS

Solution:

The clarification agent WilliamsWarn uses should easily clear

S-04, US-05, S-23, W34/70 and Nottingham yeasts. If beers

produced by these yeasts do not clear, then check you are

mixing the agent properly and that vigorous bubbling is heard

during the clarification process. If mixing is proper then any

unclear beverage using these yeast may be a random biological

occurrence or extra ingredients added (via the Advanced

Method) are making the beverage harder to clear. The haze in

this case may be small hop or malt particles that are difficult

to clear. Try an extra clarification with 30ml but be aware small

hops or malt particles may not react with our fining agent.

T-58 and WB-06 yeasts may sometimes be difficult to clear so

in these cases you can try:

1. An extra clearing with 30ml

2. Give the beverage more time to clear

3. Enjoy a slightly cloudy beverage

4. Or experiment with an alternative finings agent

Other yeast used will vary in their ability to be cleared with our

finings agent. If crystal clear beer is important to you then chose

yeast that are easy to clear with our agent or find another liquid

agent to dose.

STAGE SIX:

DISPENSE

PROBLEM 1:

THE BEVERAGE IS FOAMING TOO MUCH

Solutions:

1. Ensure you are pulling the tap handle not pushing it. Pushing

the tap handle creates foam (its used for the last part of a beer

pour). Pull the tap handle instead of pushing it.

2. Ensure you have the tap flow controller fully closed (pushed

up) before you pull the tap handle and then slowly open it

to start with a slow pour. The first pour of the day can be

foamy due to the line being warmer than the vessel and the

carbon dioxide coming out of solution in the line.

3. Ensure the draft tap is pulled out fully when pouring.

4. Ensure the beverage is cold.

5. Ensure the beverage wasn’t fermented at an extreme pressure

or is being dispensed at a too high pressure. Release excess

pressure from the vessel via the VPRV button and set at 1 bar

and try pouring again. You may need to wait for excess gas

in the beverage to move out of the beverage over time (e.g.

1 day). Try to control the pour with the control level and

pour slowly.

PROBLEM 2:

THE PRESSURE IN THE TANK SEEMS TO BE FALLING

Solutions:

1. Ensure that the gas cylinder is connected to the vessel

during dispense. The 3-way valve should be turned to the

arrow pointing to the vessel pressure gauge during dispense.

If not, as you pour the pressure in the vessel will reduce.

2. Check the gas cylinder has pressure on its high and low

pressure gauges and isn’t empty. If it is then connect a full

gas cylinder.

3. Close the 3-way valve (X position), record the vessel

pressure and don’t pour any beer for 24 hours. Read the

pressure again. If there is a major reduction you may have a

leaking seal or VPRV. See solutions 1 and 2 for Problem 2

in Stage 3 above.

PROBLEM 3:

THE BEVERAGE FLOW IS SLOW

Solutions:

1. Ensure the tank pressure is adequate. At 1.25 bar a fast

flow can be achieved when the flow control lever is fully

open and the tap pulled fully towards you.

2. Ensure the flow control lever is pushed down enough to

open and allow a flow.

3. Ensure the draft tap is being pulled all the way to its fully

open position.

Содержание BrewMaster

















































































Результаты поиска

Содержание BrewMaster

Отзывы:

WILLIAMSWARN BrewMaster, Руководство пользователя, Страница: 80 / 80

Результаты поиска

Содержание BrewMaster

Отзывы: