WILLIAMSWARN BrewMaster Скачать руководство пользователя страница 34

Страница: 34 / 80

using 30ml again. Make sure the tank valve is closed

before you clarify and only open it after the pot rinsing step.

Belgian and Wheat beer yeast can be very hard to clear at

times, but all others should be okay after 3 clarifications,

especially once the bulk of the settled yeast is removed to

give the 3rd clarification a better chance of working. If not,

it’s likely a quirk of brewing and the yeast for some reason

are not playing ball (relating to static electrical charges on

the yeast cell walls) and for some biological reason that is

hard to understand, they just won’t settle and you’ll have

to wait a few more days for it to happen over more time.

Or just consume the more hazy beer and move on to

the next brew. In 95% of brews using ale or lager yeast,

the yeast should clear without too much drama and two

clarifications are enough. For the Belgian and Wheat beer if

3 clarifications don’t do it, they will likely need quite some

days to clear by settling naturally so it’s likely its easier just

to accept some haze (as in the commercial examples of these

beer styles) and enjoy their flavours as you consume them.

full of sediment or more (see Figure 52), depending on the

yeast and beverage type.

SECOND CLARIFICATION

A second clarification can take place 24 hours after the first

clarifications so in general, Day 5½ for ales and Day 7½ for

lagers.

15. Close the vessel valve (to avoid disturbing the settled

yeast) and close the 3-way valve (X position). Then perform

another clarification as described above from steps 7 – 13

with 20ml of clarifying agent. Ensure the last step (step 13)

of turning the 3-way valve to the tank is performed so that

the beverage can equilibrate with the CO

cylinder pressure.

16. Then open the vessel valve to allow a second lot of new

sediment to settle over another 24 hour period at least, but

36 hours in general. The new sediment will push down on

the first lot of sediment and in most cases both lots will

be in the bottle over this time period and the sediment

bottle should be about ¾ full of sediment (see Figure 53)

depending on the yeast and beverage type and there should

be some clear beverage above that.

As explained in Appendix 8, some yeast are harder to clarify

than other yeast and as you brew more you will gain more

experience in this aspect of brewing.

WHAT TO DO IF YOUR BEER ISN'T CLEAR YET

1. If after the second clarification the yeast looks settled but

the yeast/haze is above the tank valve and cloudy beer is

being poured, then pour off a pint. Often the line of clearer

beer is just above the valve and excess sediment can be

taken out the beer tap and clear beer will follow. Then just

remove the sediment bottle as per normal at the end of a brew.

2. Alternatively, you can also just wait another day for it to

compact into the bottle more. The sediment is quite “fluffy”

and compacts more and more each day.

3. If the yeast looks unsettled and messy, and there are

volcanoes erupting and CO

bubbles shooting up into the

tank, then the yeast is misbehaving and clarification is

being compromised. The best thing to do would be to close

the tank valve, remove the sediment bottle like you do when

you first clarify, and dump that sediment and rinse the

bottle. Fill the sediment bottle up with foam from the tap as

you do during clarification and put it back on the brewery.

Make sure the gas cylinder is onto the vessel to maintain

pressure as it should be at this stage. Then very gently

open the valve and let the beer that’s in the cone drop

into the sediment bottle. You might want to do this over a

few openings and closings to let it settle without shooting

back up into the tank e.g. 10 little openings and closings

with a 10 second break between each opening. When the

sediment bottle is full, open the valve fully and leave that

overnight. Hopefully it’s then clear. Usually you’ll find you

just have some sediment above the valve and it’s only a few

inches that settles overnight. But at least the beer has a

chance to settle better without erupting yeast delaying it.

You hopefully can see the beer line easily and it clears up by

this extra day.

4. If the beer still isn’t clear, it may take a 3rd clarification.

So after performing point 3 above, just do a 3rd clarification

Fig. 53

Содержание BrewMaster

















































































Результаты поиска

Содержание BrewMaster

Отзывы:

Похожие инструкции для BrewMaster

Бренды по названию

Популярные бренды

WILLIAMSWARN BrewMaster, Руководство пользователя

Результаты поиска

Содержание BrewMaster

Отзывы:

Похожие инструкции для BrewMaster

Бренды по названию

Популярные бренды