WIKA IPT-2 Series Скачать руководство пользователя страница 18

Страница: 18 / 76

4 Mounting

WIKA Operating Instructions - Process pressure transmitter IPT-2x

Differential pressure on orifice: 50 mbar = 0.050 bar
Total pressure: 0.8 bar + 0.05 bar = 0.85 bar
Instrument selection

Nominal measuring range Master: 1 bar
Nominal measuring range Slave: 1 bar
Turn Down: 1 bar/0.050 bar = 20 : 1

The measuring result (level, pressure difference) as well as meas-

ured value Slave (static or superimposed pressure) are output by the

sensor. Depending on the instrument version, output as 4 … 20 mA

signal or digitally via HART, Profibus PA or Foundation Fieldbus.

4.4 Level measurement

The master/slave combination is suitable for level measurement in a

pressurized vessel
Keep the following in mind when setting up the measuring system:

•

Mount the master sensor below the min. level

•

Do not mount the master sensor close to the filling stream or

emptying area

•

Mount the master sensor so that it is protected against pressure

shocks from the stirrer

•

Mount the slave sensor above the max. level

Fig. 11: Measurement setup, level measurement in pressurized vessel
1 IPT-2x

2 IPT-2x, slave sensor

Output measured values

Measurement setup

Содержание IPT-2 Series













































































Результаты поиска

Содержание IPT-2 Series

Отзывы:

Бренды по названию

Популярные бренды

WIKA IPT-2 Series, Руководство по эксплуатации

Результаты поиска

Содержание IPT-2 Series

Отзывы:

Бренды по названию

Популярные бренды