Welker INFLOW Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 41

background image

29

IOM-161

MODEL: INFLOW™ ACE WITH AI CONTROL™

REV: D

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Disassembling the Upper Housing

19.

Unscrew the machine screws from the top cap and carefully remove the top cap from the motor housing (

).

20.

Unscrew the setscrews from the base of the packing gland body (

21.

Unscrew the packing gland body from the outer shaft.

22.

Unscrew the packing gland body from the motor housing, and then carefully remove the packing gland body from the

insertion shaft. Take care not to scratch or otherwise damage the insertion shaft assembly.

23.

Remove the dustcover from the packing gland body.

24.

Loosen the setscrews in the upper and lower lock collars on the external adjustment body, and then remove the lock

collars from the insertion shaft assembly (

). Take care not to misplace the pins that align the lock collars with

the external adjustment body.

Figure 14: External Adjustment Assembly

25.

Carefully slide the external adjustment body off the insertion shaft. Take care not to scratch or otherwise damage the

insertion shaft assembly.

26.

Carefully pull the insertion shaft out through the motor housing.

«
...
27
28
29
30
31
...
»

Содержание INFLOW










































Отзывы:

Нет отзывов

Похожие инструкции для INFLOW

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: Tascam Страницы: 128

Бренд: ParaBody Страницы: 6

Бренд: Danelec Страницы: 67

Бренд: Datalogic Страницы: 20

Бренд: Datalogic Страницы: 188

Crouse-hinds series

Бренд: Eaton Страницы: 32

Бренд: Patty-O-Matic Страницы: 28

Бренд: Ibiza Страницы: 21

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

Бренд: Yamaha Страницы: 48

Бренд: MAGSTIM Страницы: 86

Бренд: Tadano Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды