Welker INFLOW Скачать руководство пользователя страница 5

Страница: 5 / 41

1.3 Important Information

The lubrication port should remained plugged at all times except when performing maintenance on a sampler that has

been isolated from pipeline pressure and/or removed from the pipeline.

Prior to injecting Welker Great Barrier Sealant™ into the lubrication port, the plug must be removed and an

appropriately sized grease fitting installed.

After Welker Great Barrier Sealant™ has been injected into the lubrication port, the grease fitting must be removed and

the plug reinstalled before the sampler can be exposed to pipeline pressure and returned to operation.

Failure to remove the grease fitting and return the plug to the lubrication port prior to exposing the sampler to pipeline

pressure could result in a product leak and/or injury to the operator.

1.4 Specifications

The specifications listed in this section are generalized for this equipment. Welker can modify the equipment according to your

company's needs.

Please note that the specifications may vary depending on the customization of your equipment.

Table 1: inFlow™ ACE Specifications

Products Sampled

Condensate, Crude Oil, Liquid Products Compatible With the Materials of
Construction, Refined Hydrocarbons, and Water

Materials of Construction

316/316L Stainless Steel Wetted Parts, Carbon Steel Lubricator Body, PTFE, Kalrez®
Wetted Seals, and Viton® Non-Wetted Seals
Others Available

Maximum Allowable
Operating Pressure

150 ANSI Carbon Steel:

285 psig @ -20 °F to 100 °F (

19 barg @ -28 °C to 37 °C

)

600 ANSI Carbon Steel:

1480 psig @ -20 °F to 100 °F (

102 barg @ -28 °C to 37 °C

)

Pipeline Connection

Size:

Rating:

150 or 600 ANSI RF

Sample Outlet Connection

¼" FNPT

Motor Housing Actuation Ports

¼" FNPT
½" FNPT
³⁄₈" FNPT (Standard)

Insertion Length

0–18" (

0–45 cm

)

0–24" (

0–60 cm

)

0–36" (

0–91 cm

)

Utility Requirements

Hydraulic or Pneumatic Supply for Motor Operation:

120 psig (

8 barg

)

Inert Gas Supply for Purge Operation:

¼" FNPT Connection

Sample Volume

D-Style Collection Head:

0.5–10 cc

Features

External Adjustment
External Sand Relief
Purge Tube
V-ring Packing

Options

Pre-Set Collection Head
NACE Compliance

IOM-161

MODEL: INFLOW™ ACE WITH AI CONTROL™

REV: D

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Содержание INFLOW










































Результаты поиска

Содержание INFLOW

Отзывы:

Похожие инструкции для INFLOW

Бренды по названию

Популярные бренды

Welker INFLOW, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание INFLOW

Отзывы:

Похожие инструкции для INFLOW

Бренды по названию

Популярные бренды