Welker INFLOW Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 41

background image

2.4 Setting the Sample Volume

1.

To set or adjust the sample volume, locate the external adjustment assembly, and then slide the dustcover down to

expose the external adjustment chamber (

).

Setting the sample volume is accomplished by:

• determining where the adjustment pin will need to be placed to attain the desired sample volume,

• rotating the upper external adjustment ring in relation to the adjustment pin setting to attain the desired sample

volume, and

• installing the adjustment pin to the predetermined slot.

The sample volume is determined by the distance between the upper external adjustment ring and the adjustment pin.

Once the desired volume is set, the sample volume can be changed at any time externally without removing the inFlow™ ACE

from the pipeline.

Figure 7: Upper Housing Diagram

2.

Determine to which slot the adjustment pin will be installed after the external adjustment rings have been set (

16

IOM-161

MODEL: INFLOW™ ACE WITH AI CONTROL™

REV: D

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

«
...
14
15
16
17
18
...
»

Содержание INFLOW










































Отзывы:

Нет отзывов

Похожие инструкции для INFLOW

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Бренд: Nemco Страницы: 13

Бренд: Ecco Страницы: 12

Бренд: UMF Medical Страницы: 12

Бренд: p-light Страницы: 28

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: Idmed Страницы: 2

Бренд: Labelmate Страницы: 61

Бренд: Labconco Страницы: 62

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 11

Бренд: uniprox Страницы: 3

Бренд: Tieline Страницы: 359

Бренд: SAC Страницы: 2

Fast Track Solo

Бренд: Avid Technology Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды