Welker INFLOW Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 41

background image

2.3 Installing the Unit

1.

Close all valves on the inFlow™ ACE.

2.

Secure the inFlow™ ACE to a full port pipeline isolation valve.

For long probes installed horizontally, Welker recommends field installation of bracing support for the outlet end of the probe

to offset the cantilever effect and prevent bending of the shaft. Any bracing or support installed should NOT contact the probe

shaft, as scratching or other damage to the shaft may lead to loss of integrity of the sealing surface.

The vent (drain) outlet on the lubricator body must be pointed down.

If the unit will be inserted using hydraulic fluid, continue to step 3.

If the unit will be inserted using an auxiliary gas, proceed to step 13.

If the unit will be inserted using pipeline product, proceed to step 24.

11

IOM-161

MODEL: INFLOW™ ACE WITH AI CONTROL™

REV: D

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

«
...
9
10
11
12
13
...
»

Содержание INFLOW










































Отзывы:

Нет отзывов

Похожие инструкции для INFLOW

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: Haigh Страницы: 60

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

Бренд: Campbell Страницы: 2

Бренд: Tabi Страницы: 8

Бренд: Dabi Atlante Страницы: 102

Бренд: NatureZap Страницы: 2

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: Rainbow Страницы: 35

Бренд: Rain Harvesting Страницы: 2

Бренд: U-Line Страницы: 3

Бренд: U-Line Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды