Welker INFLOW Скачать руководство пользователя страница 39

Страница: 39 / 41

Figure B1: D-Style Collection Head With Sand Reliefs

Loosen the jam nut and unscrew the collection head assembly from the outer shaft.

Unscrew the piston from the insertion shaft to expose the internal sand relief. If wrenches are needed, place the

wrenches on the wrench flats.

Internal Sand Relief

Examine the seat of the internal sand relief for damage or wear. Replace as necessary.

As necessary, replace the O-rings on the seat of the internal sand relief.

Examine the spring of the internal sand relief for damage or wear. Replace as necessary.

Examine the poppet of the internal sand relief for damage or wear. Replace as necessary.

Piston and Cylinder

Inspect the bushing for signs of wear. Replace as necessary.

Replace the O-ring, back up, and PolyPak® on the piston.

Inspect the plated cylinder for scratches or other damage. Polish or replace as necessary.

10.

Unscrew the cylinder base and relief cap from the cylinder.

11.

Replace the O-ring on the cylinder.

APPENDIX B: D-STYLE COLLECTION HEAD MAINTENANCE

IOM-161

MODEL: INFLOW™ ACE WITH AI CONTROL™

REV: D

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

Содержание INFLOW










































Результаты поиска

Содержание INFLOW

Отзывы:

Похожие инструкции для INFLOW

Бренды по названию

Популярные бренды

Welker INFLOW, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание INFLOW

Отзывы:

Похожие инструкции для INFLOW

Бренды по названию

Популярные бренды