Welker INFLOW Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 41

background image

Welker recommends using a felt tip pen to mark the front of both external adjustment rings so that it is clear when the

adjustment rings have made a full rotation.

4.

Using the provided external adjustment tool, turn the upper external adjustment ring to the desired volume (

One full rotation of the upper external adjustment ring is approximately 1 cc if the inFlow™ ACE is equipped with the D-Style

collection head. Each hole in the upper external adjustment ring is equal to approximately 0.10 cc.

5.

Turn the lower external adjustment ring until it meets the upper external adjustment ring. Tighten firmly to prevent
slippage that might lead to inconsistencies in sample volume.

The lower external adjustment ring and O-ring are used to lock the upper external adjustment ring in place to prevent slippage

and subsequent changes in the sample volume during sampling.

6.

Slide the dustcover up to cover the external adjustment chamber (

7.

Install the adjustment pin through the dustcover to the appropriate slot.

8.

Turn ON and actuate the hydraulic or pneumatic supply to collect a sample from the sample outlet to ensure that the
sample volume collected is the same as the desired sample volume.

Welker recommends the Welker Checkpoint™ Sample Bite Verification Panel for use with this unit.

9.

As necessary, repeat steps 1–8 to further adjust the sample volume.

18

IOM-161

MODEL: INFLOW™ ACE WITH AI CONTROL™

REV: D

13839 West Bellfort Street, Sugar Land, TX 77498

welker.com

Service Department 281.491.2331

«
...
16
17
18
19
20
...
»

Содержание INFLOW










































Отзывы:

Нет отзывов

Похожие инструкции для INFLOW

Бренд: Tacx Страницы: 2

Бренд: C.E. Nierhoff & Co Страницы: 7

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: CAMPAGNOLA Страницы: 209

Бренд: XanLite Страницы: 4

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

Бренд: Yamaha Страницы: 139

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 32

Zen-O lite RS-00600

Бренд: GCE Страницы: 20

Бренд: Zafferano Страницы: 28

Бренд: Basler Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды