Welch Allyn Propaq LT 802LT0N Скачать руководство пользователя страница 5

Страница: 5 / 80

Safety summary

All users of the monitor must read this safety summary and all warning and caution
statements in the manual.

Warnings

WARNING

Place the monitor and accessories in locations where they cannot

harm the patient should they fall from a shelf or mount.

WARNING

Do not connect more than one patient to a monitor.

WARNING

Do not connect more than one monitor to a patient.

WARNING

Do not use the monitor in an MRI suite or hyperbaric chamber.

WARNING

To avoid explosion, do not operate the monitor in the presence of

flammable anesthetics.

WARNING

Do not use cables with abraded or broken insulation.

WARNING

Do not use a monitor that has been damaged. If a monitor has been

damaged, remove it from service until it has been verified for proper operation by
qualified service personnel.

WARNING

Use only accessories approved by Welch Allyn. Visit

www.welchallyn.com

. The use of any other accessories can result in inaccurate

patient data, can damage the equipment, and can void your product warranty.

WARNING

Always use accessories according to the standards of your facility

and according to the manufacturer's directions.

Caution

Do not use cables that do not operate properly.

Caution

Do not autoclave the monitor.

Caution

Autoclave accessories only if the manufacturer’s instructions direct you

to do so. Many accessories can be severely damaged by autoclaving.

Содержание Propaq LT 802LT0N

















































































Результаты поиска

Содержание Propaq LT 802LT0N

Отзывы:

Похожие инструкции для Propaq LT 802LT0N

Бренды по названию

Популярные бренды

Welch Allyn Propaq LT 802LT0N, Руководство по обслуживанию

Результаты поиска

Содержание Propaq LT 802LT0N

Отзывы:

Похожие инструкции для Propaq LT 802LT0N

Бренды по названию

Популярные бренды