Weil-McLain WM97+110 Скачать руководство пользователя

Страница: 59 / 132

Part number 550-142-085/0712

– 59 –

WM97+

gas

fired

water

boiler

—

Boiler Manual

Legend — Figure 66

The boiler internal primary/secondary by-pass valve must be CLOSED

for multiple boiler installations

piped as shown in this manual. This allows the boiler internal circulator to circulator water to and from the manifolds.

Flow/check valve (integral to each

boiler internal circulator)

Isolation valves (when used)

Cap

Easy-Fit® Manifold (supply) —

layout and size per page 55

Easy-Fit® Manifold (return) —

layout and size per page 55

Heating system circulator (ex-

changer tube-side)

Heat exchanger shell-side circulator

Expansion tanks (diaphragm type)

System air eliminator

System automatic air vent

Cold water supply connections

Boiler circulator — circulates water

between boiler and Easy-Fit® Manifolds

Heating system supply

Heating system return

Boiler relief valve and discharge piping,

installed per WM97+ Boiler Manual

Notes:

1. Contact heat exchanger manufacturer for heat exchanger

shell-side and tube-side piping and circulator require-

ments. Tube-side flow and temperatures must meet

heating system requirements.

2. Contact heat exchanger manufacturer for sizing heat

exchanger.

3. Heat exchanger shell-side circuit requires its own expan-

sion tank as shown.

4. Heating system circuit requires its own expansion tank,

as shown, plus its own relief valve set to protect heating

system and heat exchanger piping and components.

5. When individual isolation valves are used, individual

boiler and level controls may be required.

Figure 66

Piping layout — typical piping for multiple WM97+ boilers, using isolation exchanger (shown using

WM97+155 boilers — adjust boiler connections as required for other boiler models)

Use isolation heat

exchanger for:

Large volume systems with high
mineral content in water.

Systems exposed to untreated
quantities of makeup water.

Old systems severely contami-
nated with scale and rust buildup
inside piping and heat distribu-
tion units.

Process applications.

Commercial service water ap-
plications.

High water pressure applications,
requiring pressure relief setting
in heating system more than 30
PSIG (tall buildings). See notes
below.

Multiple boiler installations

(continued)

Heat exchanger type —

The illustration shows a

shell and tube exchanger.

Other exchanger types

may be used if suitable for

the system water condi-

tions.

Содержание WM97+110





































































































































Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды

Weil-McLain WM97+110, Руководство пользователя

Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды