Weil-McLain WM97+110 Скачать руководство пользователя

Страница: 105 / 132

Part number 550-142-085/0712

– 105 –

WM97+

gas

fired

water

boiler

—

Boiler Manual

Troubleshooting

(continued)

Display

Condition

Diagnostics

Corrective Action(s)

TEMPERATURE

SENSOR

Occurs if a temperature

sensor has electrically shorted

(SHORT) or has become

disconnected (OPEN).

Will automatically reset if the

condition clears

Check all the temperature readings of the boiler on the DIAGNOSTICS -

TEMPERATURES menu to determine if any sensors are currenty displayed

as SHORT or OPEN. Compare this to the boiler temperatures recorded

in the DIAGNOSTICS - ERRORS - LOCKOUT HISTORY # - TEMPERATURES

during the last several lockout conditions.

Determine which sensors are suspect and measure their resistance

value and compare it to the values shown in

Figure 104, page 101

. If the

resistance values are incorrect replace the temperature sensor. Refer to

repair parts section for proper part number.

OUTDOOR TEMP is the optional outdoor air temperature sensor. If this

are not being used they will always be shown as OPEN. This is normal

unless the sensors were installed.

Check wire harness for loose connections and pin engagement at sensor

connection, chassis mount connection through control housing, and the

WM97+ control. Unplug connection at sensor and at WM97+ control

and check continuity between ends.

If problem persists after checking items above replace WM97+ control.

Refer to repair parts section for kit number.

Occurs if dual temperature

sensors values have spread by

more that 10ºF if the burner

is on

Automatically resets when

sensors are within 10ºF.

Follow procedure for above for SHORT and OPEN sensor conditions

to properly diagnose sensor. If measured resistance values of sensors

convert to temperatures seperated by more than 10ºF replace the sensor.

FLUE TEMP

TOO HIGH

Occurs if flue temperature

sensor exceeds 216ºF

Automatic reset occurs if

temperature drops below 216ºF

for 2.5 minutes.

Manual reset is required if the

temperature rises above 225°F.

Reset using manual reset screen

on display

Follow procedure for above for SHORT and OPEN sensor conditions

to properly diagnose sensor. In addition inspect heat exchanger

combustion chamber and flueways for abnormal wear or buildup.

Inspect vent system for abnormal wear or damage.

Contact Weil-McLain Technical Support.

LOW WTR

CUTOFF OPEN

Occurs if internal low water

cutoff contacts open

Automatic reset occurs if

contacts are open at least one

second, but less than 5 seconds

Manual reset of WM97+ control

if contacts are open longer than

5 seconds

Check for low water condition in system. Repair system as necessary

refer to piping section of this manual.

If low water condition does not exist, check Diagnostics — Inputs screen

to view status of Low Water Cutoff. If shown as OPEN check wiring

between LWCO and WM97+ control. If wiring is alright, then replace the

LWCO.

TANK SENSOR

FAULT—TOP

CWH installations only:

Occurs if Upper Tank Sensor

has electrical shorted (SHORT)

or has become disconnected

(OPEN).

Will automatically reset if the

condition clears.

Check temperature readings in the DIAGNOSTICS — TEMPERATURES

menu to determine if any sensors currently display SHORT or OPEN.

Determine which sensor is suspect and measure its resistance value and

compare it to the value shown in

Figure 104, page 101

. If the resistance

value is incorrect, replace the temperature sensor. Refer to the repair

parts section for proper part number.

TANK SENSOR

FAULT—

BOTTOM

CWH installations only:

Occurs if Lower Tank Sensor

has electrical shorted (SHORT)

or has become disconnected

(OPEN). Boiler and Tank still

operate, but DHW production

will be limited because

control is unable to sense

cold water flowing into the

tank are respond quickly.

Tank still operates based on

Upper Tank Sensor only. Will

reset fault and resume normal

operation when lower sensor

condition clears.

Check temperature readings in the DIAGNOSTICS - TEMPERATURES menu

to determine if any sensors currently display SHORT or OPEN.

Determine which sensor is suspect and measure its resistance value and

compare it to the value shown in

Figure 104, page 101

. If the resistance

value is incorrect, replace the temperature sensor. Refer to the repair

parts section for proper part number.

DISPLAY COMM

Occurs if display

communications out for 30

seconds

Automatically resets when

communication is re-

established.

Check for a loose connection at the molex plug on the control and

connection on the back of the display.

Troubleshooting

(continued)

Figure 110

Troubleshooting suggestions for WM97+ boilers —

Fault displays, diagnostics and corrective actions

(cont.)

Содержание WM97+110





































































































































Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды

Weil-McLain WM97+110, Руководство пользователя

Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды