Weil-McLain WM97+110 Скачать руководство пользователя

Страница: 84 / 132

Part number 550-142-085/0712

WM97+

gas

fired

water

boiler

—

Boiler Manual

– 84 –

MAINTENANCE, DATE AND TIME menus

Maintenance Info

Name

text

blank

Contractor name to appear in maintenance reminders and during lockouts

Phone

text

blank

Contractor phone number

Model

text

blank

Displays the boiler model selected in the boiler setup

CP Number

text

blank

Enter the CP# of the boiler

Installed

text

blank

Enter the date the boiler was installed

Last Date

text

data

Date automatically entered when Reset Reminder is chosen by contractor

Next Date

text

data

Date automatically calculated when Reset Reminder is selected by contractor

Interval Settings

months

Contractor selects maintenance reminder frequency based on service history

Reset Reminder

Contractor selects this to update Last maintenance Date and Next Date. Homeowner uses
this to ignore the reminder and update only the Next Date.

Set Time and Date

Year

text

2011

Set year (homeowner or contractor)

Month

text

Set month (homeowner or contractor)

Day

text

Set day (homeowner or contractor)

Hour

text

Set hour (homeowner or contractor)

Minute

text

Set minute (homeowner or contractor)

Figure 92

MAINTENANCE, DATE AND TIME

menus — navigation (see Figure 80, page 72 for access information)

Figure 93

MAINTENANCE, DATE AND TIME

menus — details (see Figure 92 for access information)

MAINTENANCE INFO

NAME

PHONE

MODEL

CP#

INSTALLED

LAST DATE

NEXT DATE

INTERVAL SETTINGS

RESET REMINDER

################

###-###-####

WM97+ ###

##########

MM/DD/YY

DD/MM/YY

## MONTHS

PRESS ENTER TO RESET

SET DATE AND TIME

SET YR/MN/DAY/HR/MIN

MAINTENANCE INFO

1. Use this section to enter contractor’s information and to

enter an automatic notice for maintenance (default is 12

months). Because this shows on the display, it is an automatic

means of notifying the homeowner of need for scheduled

maintenance by the technician. Update the screen reminder

to reset for the next maintenance date.

Содержание WM97+110





































































































































Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды

Weil-McLain WM97+110, Руководство пользователя

Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды