Weil-McLain WM97+110 Скачать руководство пользователя

Страница: 104 / 132

Part number 550-142-085/0712

WM97+

gas

fired

water

boiler

—

Boiler Manual

– 104 –

Troubleshooting

(continued)

Display

Condition

Diagnostics

Corrective Action(s)

Nothing shown

on display

screen and

boiler will not

respond to call

for heat

Control is not receiving 24V

power

Check wiring for short circuit or

incorrect wiring.

Correct wiring per wiring diagram including connection of transformer

to the WM97+ control.

Check 3-amp low voltage fuse

on WM97+ control shown on

page 101

Replace fuse with proper part found in replacement part section of this

manual. If fuse blows again recheck wiring per diagram.

Check transformer connection

to the WM97+ control per

wiring diagram. Check for 24V

output of transformer.

Replace transformer if it is is receiving 120Vac, but not outputting 24Vac.

Nothing

is shown

in display

screen and no

other boiler

components are

operating

Control is not receiving 120V

power

Check service switch and/or

circuit breaker to boiler turned

is on.

Turn on service switch to power boiler.

Is there 120 Volts at the service

switch?

Troubleshoot and correct the power supply to the service switch.

Is the WM97+'s ON/OFF POWER

SWITCH located on top of the

boiler

Turn the WM97+'s power switch to ON.

Check for 120 volts at the line

voltage terminal block located

inside the top left electrical

compartment

Correct wiring inside the control pod using the wiring diagram in this

manual.

Inspect 12-amp fuse as shown

page 101

. Replace if

necessary.

Replace the fuse with proper part found in the replacement part section

of this manual. If fuse blows again recheck wiring per diagram.

Nothing is

shown on

display screen,

but boiler is

operating

Occurs if the communication

is lost from the WM97+

control to the display.

Check for loose connections

and proper pin alignment/

engagement on the WM97+

control's plug P9 and the back

of the display circuit board.

Check for continuity on the wire harness from the display to the WM97+

control. See repair parts section for proper replacement part.

Cycle power off and on using

boiler power switch and check

for operation.

Replace with new display module. See repair parts section for proper

replacement part.

TEMP RISE TOO

QUICKLY

Occurs if supply water

temperature in heat

exchanger rises faster than

2ºF per second during the

first two minutes the burner

is on.

Automatically resets after 1

minute delay or using manual

reset on display.

Manual reset is necessary after 5

automatic resets have occurred

during the same Priority heat

demand. Reset using manual

reset screen on display

Verify water pipe is installed correctly per instructions in this manual.

Verify proper circulator and speed for boiler size and system

requirements.

See message displayed TEMPERATURE SENSOR and follow procedure for

loose connections.

SUPPLY 58F >

RETURN

Boiler Out temperature

has exceeded the Boiler In

temperature by more than

58ºF

Automatically resets after 30

second delay or using manual

reset on display.

Verify water pipe is installed correctly per instructions in this manual.

Verify proper circulator and speed for boiler size and system

requirements.

See message displayed TEMPERATURE SENSOR and follow procedure for

loose connections.

RETURN >

SUPPLY

Occurs if a return water

temperature is greater than

the corresponding supply

temperature by 10ºF or more.

Automatically resets when

condition no longer exists.

Verify proper flow direction of the boiler circulator. This circulator must

be installed to push water through the boiler's return pipe as shown on

page 38.

Verify proper boiler circulator speed setting in the WM97+ control.

Figure 110

Troubleshooting suggestions for WM97+ boilers —

Fault displays, diagnostics and corrective actions

Содержание WM97+110





































































































































Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды

Weil-McLain WM97+110, Руководство пользователя

Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды