Weil-McLain WM97+110 Скачать руководство пользователя

Страница: 107 / 132

Part number 550-142-085/0712

– 107 –

WM97+

gas

fired

water

boiler

—

Boiler Manual

Display

Condition

Diagnostics

Corrective Action(s)

BLOWER FAULT

Blower unable to reach

required speed or does not

reach 0 RPM when turned off.

NOTICE: WM97+70 or 110

only — The blower will not

rotate without a low voltage

signal. Unplugging the low

voltage blower wire harness

will not allow or cause the

boiler to rotate.

Reset using manual reset screen

on display; WM97+ control will

check again after 1 hour and will

automatically restart if condition

is corrected

Check wire harness for loose connections and pin engagement at blower

connections, chassis mount connection through control housing, and

WM97+ control. Unplug connection at blower and at WM97+ control

and check continuity between ends. Blower is connected to both low

voltage and line voltage harness.

Check Diagnostics - Inputs screen with boiler in standby mode and

blower not running. If BLOWER SPEED is not 0 RPM then replace blower.

If blower does not rotate during ignition sequence check for 120V power

at blower connection. If 120Vac power at blower motor and it doesn't

start replace blower. Check power at WM97+ control. If 120Vac is not

present at WM97+ control when boiler is powered replace WM97+

control. Refer to repair parts section.

IGNITION

FAULT

Boiler went through 5 ignition

attempts and never detected

flame

Automatically resets after 1 hour

or can be reset by performing

manual reset on boiler.

Check condensate trap for blockage allowing condensate to accumulate

inside heat exchanger.

Check ignition cable connection.

Fouled, worn, bent, or faulty igniter.

Fouled igniters can be cleaned for additional use with steel wool.

Worn or badly fouled igniters should be replaced with the proper repair

part.

Igniter rods should be parallel with a 3.5 mm (0.138 in) spark gap.

NOTICE: Thin white deposits on the igniter are typical, but brown or

black deposits could be the result of flue gas recirculation. Thoroughly

inspect the venting system and termination for the possibility of leakage

or flue gas feedback into the air line.

Dirty burner and/or heat exchanger will cause high back pressure and

poor ignition.

Follow procedure in maintenance section of this manual to clean burner

and heat exchanger. Visual inspection of flueways may not be sufficient

to diagnose condition.

Check combustion settings on high and low fire and adjust per setup

instructions if necessary.

Check incoming gas pressure with boiler off and at high fire. Adjust

within limits on rating label.

Verify correct boiler model is selected in control and high altitude is

selected for installations 5,500 feet above sea level.

Check ignition cable resistance. Should measure 1000 Ohms (+/- 50

Ohms)

Check for flue pipe and intake pipe restrictions or blockage

Check burner fasteners and gaskets

Check venturi gaskets and proper propane orifice bushing

Troubleshooting

(continued)

Figure 110

Troubleshooting suggestions for WM97+ boilers —

Fault displays, diagnostics and corrective actions

(cont.)

Содержание WM97+110





































































































































Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды

Weil-McLain WM97+110, Руководство пользователя

Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды