Weil-McLain WM97+110 Скачать руководство пользователя

Страница: 128 / 132

Part number 550-142-085/0712

WM97+

gas

fired

water

boiler

—

Boiler Manual

– 128 –

Figure 131

Dimensional data —

WM97+70/110/155

(all dimensions in inches)

Dimensions

TOP

FRONT

RIGHT

70/110

155

TOP

(shows field-installed components)

TOP

(shows field-installed components)

BOTTOM

(shows field-installed components)

BOTTOM

(shows field-installed components)

Boiler supply tapping —

1” NPT (70/110) / 1¼” NPT (155)

Boiler return tapping —

1” NPT (70/110) / 1¼” NPT (155)

Control panel, with display and navigation

buttons

Electrical entrance openings

Vent connection: 3” PVC

Pressure/temperature gauge (shipped loosed)

See Figure 6, page 12 for mounting details and

instructions.

Gas connection (note 1) (manual gas valve

shipped loose for field installation)

See page 61 for details and instructions.

Drain valve (shipped loose)

See Figure 6, page 12 for mounting details and

instructions.

Condensate drain connection (also see item 14,

below)

Air connection: 3” PVC

Relief valve (shipped loose)

See page 37 for mounting details. Relief valve

mounts on supply pipe off of supply tee and

¾” street elbow as shown.

Boiler drain line / DHW boiler water return

line (if DHW tank is connected directly to the

boiler)

See Figure 8, page 13 for details and instruc-

tions for usage.

DHW boiler water supply line (if DHW tank is

connected directly to the boiler)

See Figure 8, page 13 for details and instruc-

tions for usage.

Condensate trap and flexible drain line

(shipped loose)

See page 60 for details and instructions. The

condensate drain hose or pipe must connect to

the flexible line supplied with the boiler to en-

sure the trap assembly can be removed easily.

Содержание WM97+110





































































































































Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды

Weil-McLain WM97+110, Руководство пользователя

Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды