manualshive.com logo in svg

Weil-McLain WM97+110, Руководство пользователя

Вас приветствует продукт Weil-McLain WM97+110! Здесь вы найдете полное руководство пользователя бойлера, чтобы легче настроить его для вашего дома. Скачайте бесплатное руководство с manualshive.com, чтобы использовать все функции бойлера на полную мощность.

Поделиться
Скачать
background image

Part number 550-142-085/0712

WM97+ 

gas

-

fired

 

water

 

boiler

 — 

Boiler Manual

– 20 –

Venting & air — general

 

(cont.)

Figure 17

 

WM97+ venting and air piping — DIRECT VENT ONLY

 — OPTIONS and PIPING LIMITS

  The table below lists the acceptable vent/air pipe terminations described in this manual. Follow all instructions provided to install the 

vent/air system. 

NOT SHOWN

 below, but also approved, are the polypropylene piping and terminations listed in Figure 18, page 21. 

For these applications, use ONLY the manufacturers’ parts listed and follow all instructions provided by the pipe manufacturer.

WM97+ M

odel

Maximum vent and air pipe length = 100 feet for all applications

 

(Minimum length for all applications is 2 feet)

(All applications include allowance for the termination fittings plus one elbow in air piping and one elbow in vent piping)

USE SWEEP 

ELBOWS 

ONLY

See Figure 18, page 21 for material specifications    |    See Figure 119, page 117 for part/kit numbers

Vent and air pipe sizes:

  

Maximum vent lengths apply for either 2” or 3” vent and air pipe.  

If using 2” pipe, provide 3”x2” reducers at boiler connections and at Weil-McLain vent/air cap or at concentric terminations. 

Boilers will derate as vent/air pipe length increases — see rating data on Figure 132, page 129 for derate amounts.

SIDEWALL

 termination

VERTICAL

 termination

3” Weil-McLain PVC 

vent/air cap 

[Note 1]

Separate pipes  

[Note 1]

PVC or PP Concentric

  

[Note 1]

Separate pipes  

[Note 1]

PVC or PP Concentric

  

[Note 1]

See page 25

See page 27

See page 29

See page 31

See page 33

Size, 

inches

Materials 

Fig. 18, page 21

Size, 

inches

Materials 

Fig. 18, page 21

Size, 

inches

Materials 

Fig. 18, page 21

Size, 

inches

Materials 

Fig. 18, page 21

Size, 

inches

Materials 

Fig. 18, page 21

70

2

PVC/PVC-DWV 

CPVC, PP, SS

2

PVC/PVC-DWV 

CPVC, PP, SS

2

PVC/PVC-DWV 

CPVC, PP, SS

2

PVC/PVC-DWV 

CPVC, PP, SS

2

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, PP, SS

110

2

CPVC, PP or SS 

ONLY

2

CPVC, PP or SS 

ONLY

2

CPVC, PP or SS  

ONLY

2

CPVC, PP or SS 

ONLY

2

CPVC, PP or SS  

ONLY

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, PP, SS

155

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC,  SS, **

3

PVC/PVC-DWV 

CPVC, PP, SS

3

PVC/PVC-DWV 

CPVC, SS, **

**   Model 155 may be concentric sidewall vented (NOT vertical concentric vented) using Centrotherm polypropylene pipe (Eco 

Systems InnoFlue® Single-wall) ONLY if using Centrotherm stainless steel concentric termination kit, part number ICWS3513.

 

All elbows in vent and air piping must be sweep elbows ONLY. DO NOT use short-radius elbows.

Equivalent feet for elbows (USE SWEEP ELBOWS ONLY)

 — deduct from max equivalent length of piping (does not apply to termination fittings)

•  7 feet per for each additional 90° sweep elbow or 45° elbow —

 If piping contains more than 1 elbow in air or vent piping, other than termination fittings

Note 1: 

Material abbreviations: PP = polypropylene, SS = AL29-4C stainless steel

If using polypropylene or stainless pipe, provide adapters to for 3” boiler connections and for terminations, if required
IPEX 3” PVC concentric vent kits can be used with standard PVC pipe, fittings and cement (ANSI/ASTM D1785) except if ULC S636 compli-

ance is required. For ULC S636 compliance, all pipe, fittings and cement must be IPEX System 636. If using IPEX kits, use only IPEX product 

code 196006 for 3” venting.

Contact Weil-McLain for ordering information and availability of Weil-McLain venting kits.

Содержание WM97+110





































































































































Отзывы:

Нет отзывов

Похожие инструкции для WM97+110

IBC P-153B Replacement Instructions Manual preview
P-153B
Бренд: IBC Страницы: 7
IDEAL Mexico Super RS 3/60P User Manual preview
Mexico Super RS 3/60P
Бренд: IDEAL Страницы: 8
Daikin D2CND024A1AA Operation Manual preview
D2CND024A1AA
Бренд: Daikin Страницы: 12
Vaillant GA100CS SERIES Installation And Service Manual preview
GA100CS SERIES
Бренд: Vaillant Страницы: 12
Vaillant ecoVIT exclusiv VKK 226/4-H Operating Instructions Manual preview
ecoVIT exclusiv VKK 226/4-H
Бренд: Vaillant Страницы: 16
Alpha ARES Pro 150 Installation And Servicing Instructions preview
ARES Pro 150
Бренд: Alpha Страницы: 44
Baxi Duo-tec 2 Combi 40 GA User'S Operating Instructions & Important Warranty Information preview
Duo-tec 2 Combi 40 GA
Бренд: Baxi Страницы: 20
Riello 28 KIS Cs Installer And User Manual preview
28 KIS Cs
Бренд: Riello Страницы: 64
IBC EBX Series Installation And Operation Manual preview
EBX Series
Бренд: IBC Страницы: 68
Fondital ITACA KB 24 Installation, Use And Maintenance Manual preview
ITACA KB 24
Бренд: Fondital Страницы: 80
Radiant Slim RBA CS 24 E Installation And Maintenance Manual preview
Slim RBA CS 24 E
Бренд: Radiant Страницы: 38
Kiturami KRH-35B Technical Information And Installation Servicing Instructions preview
KRH-35B
Бренд: Kiturami Страницы: 39
IDEAL Europa 224 User Manual preview
Europa 224
Бренд: IDEAL Страницы: 6
Ariston CLAS HE R 12 Installation And Servicing Instructions preview
CLAS HE R 12
Бренд: Ariston Страницы: 64
Dunkirk DXL Series Installation, Operation & Maintenance Manual preview
DXL Series
Бренд: Dunkirk Страницы: 40
Dunkirk DPFO-3 Installation Manual And Operating Instructions preview
DPFO-3
Бренд: Dunkirk Страницы: 42
Columbia LV Series Installation, Operation & Maintenance Manual preview
LV Series
Бренд: Columbia Страницы: 32
UTICA BOILERS PEG075DID Installation, Operation & Maintenance Manual preview
PEG075DID
Бренд: UTICA BOILERS Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды