Weil-McLain WM97+110 Скачать руководство пользователя

Страница: 19 / 132

Part number 550-142-085/0712

– 19 –

WM97+

gas

fired

water

boiler

—

Boiler Manual

You must pipe combustion air to the
boiler air intake

Install air inlet piping for the WM97+

boiler as described in this manual.

The air termination fitting must be in-

stalled with the clearances and geometry

relative to the vent outlet depicted in this

manual to ensure that flue products do

not enter the air intake.

Ensure that the combustion air will not

contain any of the contaminants in Fig-

ure 16. Do not pipe combustion air near a

swimming pool, for example. Avoid areas

subject to exhaust fumes from laundry

facilities. These areas will always contain

contaminants.

Contaminated combustion air will dam-

age the boiler, resulting in possible severe

personal injury, death or substantial
property damage.

Figure 16

Corrosive contaminants and sources

Products to avoid

Spray cans containing chloro/fluorocarbons

Permanent wave solutions

Chlorinated waxes/cleaners

Chlorine-based swimming pool chemicals

Calcium chloride used for thawing

Sodium chloride used for water softening

Refrigerant leaks

Paint or varnish removers

Hydrochloric acid/muriatic acid

Cements and glues

Antistatic fabric softeners used in clothes dryers

Chlorine-type bleaches, detergents, and cleaning
solvents found in household laundry rooms

Adhesives used to fasten building products and other
similar products

Excessive dust and dirt

Areas likely to have contaminants

Dry cleaning/laundry areas and establishments

Swimming pools

Metal fabrication plants

Beauty shops

Refrigeration repair shops

Photo processing plants

Auto body shops

Plastic manufacturing plants

Furniture refinishing areas and establishments

New building construction

Remodeling areas

Garages with workshops

Venting/air piping — general

Do not install the WM97+ boiler into a common vent with

any other appliance. This will cause flue gas spillage or ap-

pliance malfunction, resulting in possible severe personal

injury, death or substantial property damage.

Existing common vent systems may be too large for the

appliances remaining connected after the existing boiler

is removed.

Failure to follow all instructions can result in flue gas

spillage and carbon monoxide emissions, causing severe

personal injury or death.

When removing a boiler from an existing

common vent system

The WM97+ boiler cannot be common vented with any other ap-
pliance

. When an existing boiler is replaced with an WM97+ boiler, the

WM97+ boiler CANNOT use the existing common vent. The WM97+

boiler requires its own vent and air piping, as specified in this manual. This

may cause a problem for the appliances that remain on the old common

vent, because the vent may be too large. The following test is intended to

check for proper operation of the appliances remaining on the old com-

mon vent system.

Vent system verification

Perform the test sequence below for

each

appliance remaining on the

original common vent system. Operate each appliance individually, with

other appliances turned off. This procedure will test whether the common

vent system can properly vent each appliance.

Existing vent test procedure

(The following is intended to test whether the appliances remaining
on an existing vent system will operate satisfactorily.)

1. Seal any unused openings in the common venting system.
2. Visually inspect the venting system for proper size and horizontal pitch

and determine there is no blockage or restriction, leakage, corrosion or

other deficiencies which could cause an unsafe condition.

3. Test vent system — Insofar as is practical, close all building doors and

windows and all doors between the space in which the appliances

remaining connected to the common venting system are located and

other spaces of the building. Turn on clothes dryers and any appliance

not connected to the common venting system. Turn on any exhaust

fans, such as range hoods and bathroom exhausts, so they will oper-

ate at maximum speed. Do not operate a summer exhaust fan. Close

fireplace dampers.

4. Place in operation the appliance being inspected. Follow the lighting

instructions. Adjust thermostat so appliance will operate continuously.

5. Test for spillage at draft hood relief opening after 5 minutes of main

burner operation. Use the flame of a match or candle, or smoke from

a cigarette, cigar, or pipe.

6. After it has been determined that each appliance remaining connected

to the common venting system properly vents when tested as outlined

herein, return doors, windows, exhaust fans, fireplace dampers, and

any other gas-burning appliance to their previous conditions of use.

Any improper operation of common venting system should be corrected

so the installation conforms with the National Fuel Gas Code, ANSI Z223.1

— latest edition. Correct by re-sizing to approach the minimum size as

determined using the appropriate tables in Part 11 of that code. Canadian

installations must comply with B149.1 or B149.2 Installation Code.

Содержание WM97+110





































































































































Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды

Weil-McLain WM97+110, Руководство пользователя

Результаты поиска

Содержание WM97+110

Отзывы:

Похожие инструкции для WM97+110

Бренды по названию

Популярные бренды