Waters 2489 Скачать руководство пользователя страница 50

Страница: 50 / 150

June 11, 2015, 715004752 Rev. A

Page 50

Field

requiring

entry

Wavelength

Selects the wavelength monitored on the

selected channel. In single-wavelength

mode, you cannot independently control

wavelength on channel B.

Channel selector

Changes the channel when you press

A/B. The icon of the selected channel

overlaps that of the other channel.

Channel On

Displays ON A or ON B for the channel a

timed or threshold event is programmed

on.

Channel trace

When you press TRACE, displays only the

channel being viewed.

Numerical

field

Absorbance

Displays current absorbance for the

selected channel.

Lamp on

Indicates the lamp is turned on.

Lamp off

Indicates the lamp is turned off.

Shift off

Blank = Shift off.

Shift on

Indicates the shift is on for one key

press.

Single-wavelength Indicates the detector is operating in

single-channel mode.

Multiwavelength

Indicates the detector is operating in

dual-channel mode.

Keypad unlock

Indicates unrestricted keypad entry.

Keypad lock

Indicates changes to parameter values

are not allowed. The keypad locks when

the instrument is under control of an

external data system (remote mode

only).

Sticky diagnostic

Indicates a sticky diagnostic setting is

active. (See

page 113

for an explanation

of sticky diagnostic settings.)

Table 3–2:

Absorbance and message screen icons (continued)

Icon or

field

Icon/field name Function

Содержание 2489






















































































































































Результаты поиска

Содержание 2489

Отзывы:

Похожие инструкции для 2489

Бренды по названию

Популярные бренды

Waters 2489, Обзор и руководство по обслуживанию

Результаты поиска

Содержание 2489

Отзывы:

Похожие инструкции для 2489

Бренды по названию

Популярные бренды