Waters 2489 Скачать руководство пользователя страница 91

Страница: 91 / 150

June 11, 2015, 715004752 Rev. A

Page 91

Recommendation:

Program the lamp to shut off or turn the lamp off manually

only if the value of the “Lamp off” parameter is more than 4 hours.

Without powering off the system, you can conserve lamp life by,

•

turning power to the lamp off and on again manually;

•

programming a timed event to turn the lamp off and on again;

•

programming the lamp to turn off and on again using the external contact

closure.

To turn power to the lamp on and off manually, use the Lamp keypad function (Shift

1). When the lamp is turned off, the absorbance screen displays the words “Lamp off”,

and the lamp icon appears with an “X” through it.

Use the Lamp key (Shift 1) to,

•

shut the lamp off or turn the lamp on manually;

•

display the number of times the lamp has ignited;

•

display the hours and minutes the lamp has been turned on during the current

run, since its installation, or both.

To turn off the lamp manually from the detector front panel:

1. Press Lamp (Shift 1) from the keypad.

Result:

The lamp control screen appears.

Figure 3–34: Lamp control screen

2. Press Lamp (Shift 1) again to turn the lamp off.

Figure 3–35: Lamp off/on sequence

To ignite the lamp manually:

1. When there is an X through the lamp icon on the absorbance screen, press

Lamp (Shift 1).

2. Press Lamp (Shift 1) again to turn the lamp on.

Lamp off indicator

Lamp on indicator

Содержание 2489






















































































































































Результаты поиска

Содержание 2489

Отзывы:

Похожие инструкции для 2489

Бренды по названию

Популярные бренды

Waters 2489, Обзор и руководство по обслуживанию

Результаты поиска

Содержание 2489

Отзывы:

Похожие инструкции для 2489

Бренды по названию

Популярные бренды