Walchem WebMaster Скачать руководство пользователя страница 176

Страница: 176 / 178

172

Temperature calibration, high/low alarm menus missing from Sensor Input page

The controller not detecting the temperature sensor at power up causes this problem.

Possible Causes

Corrective Actions

The temperature sensor is not connected.

Connect the temperature sensor and

turn power on.

Faulty temperature sensor.

Measure the temperature signal using an

ohmmeter between the green wire and the

WHT/GRN wire as close to the sensor as

possible with the wires disconnected from

the terminal strip. If the reading is infinite

ohms, replace the sensor.

Sensor input is selected to be an ORP type

This is normal. ORP inputs do not use automatic

temperature

compensation.

Link to 4-20 mA Output page does not appear

The controller not detecting any 4-20 mA output boards at power up causes this problem.

Possible Causes

Corrective Actions

No 4-20 mA output boards are installed.

Install one or more 4-20 mA output boards

and turn power on.

Poor connection of the 4-20 mA output

Remove the option board and inspect both

board.

mating connectors for corrosion or damage

Reinstall the option board on turn power on.

Link to Level page does not appear

The controller not detecting either a digital input board or an analog input board at power up
causes this problem.

Possible Causes

Corrective Actions

No digital or analog input board is installed. Install the desired option board and turn

power

on.

Poor connection of the option board.

Remove the option board and inspect both

mating connectors for corrosion or damage

Reinstall the option board on turn power on.

Link to Digital Inputs page does not appear

The controller not detecting a digital input board at power up causes this problem.

Possible Causes

Corrective Actions

No digital input board is installed.

Install the digital input option board and

turn power on.

Poor connection of the option board.

Remove the option board and inspect both

mating connectors for corrosion or damage

Reinstall the option board on turn power on.

Содержание WebMaster



















































































































































































Результаты поиска

Содержание WebMaster

Отзывы:

Похожие инструкции для WebMaster

Бренды по названию

Популярные бренды

Walchem WebMaster, Инструкция по эксплуатации

Результаты поиска

Содержание WebMaster

Отзывы:

Похожие инструкции для WebMaster

Бренды по названию

Популярные бренды