Walchem WebMaster Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 178

background image

51

5.12 Feature

Activations

This menu is used to activate all of the various communications software features in the field. If
you have purchased the controller with the communication feature, it will already be activated and
no further action will be necessary. Press Enter to view a list of any activated features.

To activate a software feature in the field, purchase the activation key file from your distributor
and save it on the root drive of a USB flash drive. Disconnect power to the controller, and insert
the flash drive into the USB Host connector on the front panel (see figure 3). Close the front panel
and restore power. Enter the Feature Activation menu. “New Activation” will be highlighted. Press
Enter to open the New Activation menu. “Start” will be highlighted. Press Enter to start the
activation process. The Status screen will display the progress and in a few seconds will show if
the process was successful or not.

As many as three activation types are possible: Modbus TCP, Sub-Networking, and one of several
communications options. If more than one feature needs to be activated, this process must be
repeated for each one.

5.13 Controller

Restart

This menu is used to safely restart the controller. This should be used instead of cycling power in
order to shut down the program in the proper manner.

6.0 OPERATION – Using PC

These units control continuously as long as power is applied. This section describes how to set up
the controller utilizing a PC. See Section 5.0 for instructions utilizing the controller keypad and
display.

When you first access the controller, the System Summary page will be displayed in the main
frame of the browser, and the Name of the controller and Alarm Status will be displayed in the top
frame. Links to each main menu page are located along the left side of the screen.
The menus are organized by inputs and outputs. Each input has menus for calibration, selecting
units of measure, etc. as required. Each output has menus for defining the set points, maximum on-
time, method of control, etc.

Keep in mind when the controller is powered, it will be responding to default set points. As set
points are changed, the controller will start using the new set points immediately. If it is
undesirable for the controller to activate valves and pumps during the set up process, either
disconnect them, or go to the “Hand-Off-Auto” menu for each output and force them “Off”.

«
...
53
54
55
56
57
...
»

Содержание WebMaster



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WebMaster

AUTOSTROKE AST-200-V2

Бренд: StoneAge Страницы: 28

Бренд: Farenheit Страницы: 8

Бренд: IBAIONDO Страницы: 7

Бренд: Labelmate Страницы: 2

Бренд: Labnet Страницы: 2

Бренд: Labona Страницы: 12

Бренд: Vaillant Страницы: 80

Бренд: Trace2O Страницы: 9

Бренд: Front Runner Страницы: 5

Home Power Hockey Table

Бренд: Great American Recreation Страницы: 10

H-BLACK PRO DYNAMO

Бренд: HERRMANS Страницы: 2

Бренд: Modern Portable Страницы: 6

Бренд: Schwinn Страницы: 12

Бренд: TeraBee Страницы: 17

Бренд: Campbell Hausfeld Страницы: 4

Docking Station for the Apple 13" MacBook

Бренд: Bookendz Страницы: 12

BASIC TLL171231

Бренд: Tellur Страницы: 5

PASPORT PS-2134

Бренд: PASCO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды