Walchem WebMaster Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 178

background image

79

Product Level

Displays the live calculated process value, using the existing 4 mA = , 20 mA = and
Dye/Product Ratio settings.

New Value

Enter the desired new reading for the ppb of fluorescent dye.

Dye/Product Ratio

The Dye-to-Product ratio is the ratio of the fluorescent dye in ppb to the active ingredient
in the chemical product in ppm. Type the ratio (given to you by your chemical supplier).
Click Continue.

At the end of the calibration, the display will tell you if the calibration was successful or if
the calibration failed. If successful, click Close to resume control. If failed, refer to Section
8 for troubleshooting help.

Reset Defaults

If for any reason you want to go back to factory default settings for the calibration coefficients,
click on the Reset Defaults button. You will be asked to verify that you want to change the
calibration. Click Yes to continue. Another window will popup to tell you that the calibration was
successful.

6.12 Flow Meter (Digital) Input Menu

All flow meters connected to digital inputs will be configured in this menu. Each meter will have a
separate section. The sections available for a contact meter will differ than those for a paddlewheel
meter.

Volume Units

Click on the radio button to select volume in units of

Gallons

,

Liters

or

Cubic Meters

. If you

change the units in this screen, changes will not occur on the page until the “Submit” button is
pressed.

Custom Name

Type in the text box a name to describe the flow meter.

Total/Reset Total

The Total displays the volume of solution to pass the flow meter since the last time the totalizer
was reset.
If you want to reset the total, click on the “Reset Total” button.

Last Total Reset

Displays the date and time that the totalizer was last reset.

Rate (only appears if the water meter type is selected as ‘Paddlewheel’)

Displays the current water flow rate through the water meter.

Status

Possible status messages are; Normal (everything is OK) or Circuit Board Failure (Digital Inputs
1-6 only). See section 8.1 for a complete description of error messages.

«
...
81
82
83
84
85
...
»

Содержание WebMaster



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WebMaster

Бренд: Manfrotto Страницы: 2

Бренд: Manfrotto Страницы: 2

Бренд: Pacbrake Страницы: 9

Action Replay DSi

Бренд: Datel Страницы: 2

Бренд: Kargo Master Страницы: 13

Бренд: Kargo Master Страницы: 21

Бренд: Kargo Master Страницы: 4

Бренд: Karel Страницы: 56

Бренд: LAS Страницы: 44

Бренд: LAS Страницы: 24

Бренд: Xantrex Страницы: 3

Бренд: Harol Страницы: 17

Бренд: Cab Technology Страницы: 10

SmartDiag2GO GD201-O

Бренд: OCTO Страницы: 5

Бренд: Conrad Страницы: 26

Бренд: Kettler Страницы: 4

Sleeptrainer Palm the penguin

Бренд: NENKO Страницы: 4

Бренд: Solight Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды