WAGO 852-1305 Скачать руководство пользователя страница 42

Страница: 42 / 314

Connect Devices

WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Pos: 24.8 /Serie 852 (ETH ERNET-Zubehör)/Anschließ en/Anschluss 10/100/1000Base-T-Ports 852-1305 @ 27\mod_1467291554066_21.docx @ 215659 @ 2 @ 1

6.5

10/100/1000BASE-T Ports

The 10/100BASE-T ports (RJ-45 ETHERNET ports) of the industrial managed

switch support both autosensing and autonegotiation.

Connect one end of the twisted pair cable of the type Category 3/4/5/5e to

an available RJ-45 port on the industrial managed switch and the other end

to the port of the selected network node.

Check the respective port LED on the industrial managed switch that the

connection is established.

(see section “Display Elements” > … > “Port LEDs”).

Pos: 25 /D okumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Содержание 852-1305



























































































































































































































































































































Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды

WAGO 852-1305, Руководство пользователя

Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды