WAGO 852-1305 Скачать руководство пользователя страница 141

Страница: 141 / 314

WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 141

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Table 46: WBM “QoS” Page – “Schedule Mode” Tab

Schedule Mode Settings
Parameters

Default

Description

Schedule Mode

High First

(SPQ)

In the selection box, select “Strict Priority Queuing

(SPQ)” if you want to process the hardware priority

queues sequentially.

Weighted

Round Robin

(WRR)

In the selection box, select “Weighted Round

Robin (WRR)” if you want to use the algorithm

based on queue weighting (the value entered in the

“

Weight Value (range: 1~127)

” field.

Queues with higher weighting get more service than

those with lower weighting.

Queue ID

0 … 7

This column displays which “Queue” is being

configured.

0 = Lowest priority

7 = Highest priority

Weight Value

(Range: 1~127)

… 127

The “Weight Value” can only be configured if the

“Weighted Round Robin (WRR)” is selected.

The bandwidth is divided among the different

“Traffic Queues” according to their weighting.

0 = Lowest priority

127 = Highest priority

Note

Changing the “Weight Value (range:

1~127)”

If you have selected “Strict Priority

Queuing (SPQ)”, you cannot change

the “Weight Value”.

You must first select “Weighted

Round Robin (WRR)”. You can then

change “Strict Priority Queuing

(SPQ)”.

Содержание 852-1305



























































































































































































































































































































Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды

WAGO 852-1305, Руководство пользователя

Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды