WAGO 852-1305 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 314

WAGO 852-1305 Скачать руководство пользователя страница 29

WAGO-ETHERNET-Zubehör 852

Device Description

29

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Pos: 19.11 /Alle Serien (Allgemeine M odul e)/Überschriften/Ebene 2/Anzeigeelemente - Ü berschrift 2 @ 4\mod_1240984390875_21.docx @ 31964 @ 2 @ 1

4.3

Display Elements

Pos: 19.12 /Serie 852 ( ETHER NET-Z ubehör)/Ger ätebeschrei bung/Anzeigeelemente/LED-Anzeigen 852-1305 @ 27\mod_1467276540667_21.docx @ 215521 @ 33 @ 1

The industrial managed switch is equipped with device LEDs and port LEDs. You

can see the status of the switch at a quick glance of the device LEDs, while the

port LEDs provide information about connection actions.

4.3.1

Device LEDs

Figure 5: Device LEDs

Table 7: Legend for Figure “Device LEDs”

LED

Name

Status Description

PWR

Primary Power

LED

Green The industrial managed switch uses the

primary power supply.

OFF The primary power supply has been

switched off or a fault has occurred.

RPS

Redundant Power

System LED

Green The industrial managed switch uses the

redundant power supply.

OFF The redundant power supply has been

switched off or a fault has occurred.

ALM

Alarm LED

Red Lights up in the event of network,

connection or ring errors (for Arbiter

nodes).

OFF No alarm to report.

POST

Power On Self Test

LED

Flashes The POST function is executed.

Green The POST is completed.

OFF No power supply or error detected in

the POST function.

«
...
27
28
29
30
31
...
»

Содержание 852-1305



























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды