WAGO 852-1305 Скачать руководство пользователя страница 254

Страница: 254 / 314

254 Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

9.6.5

System Log

The “syslog” function records various system information for “Debugging”.

Each log entry records one of the following levels:

- Alert

- Critical

- Error

- Warning

- Notice

- Information

The Syslog function can be enabled or disabled. The default setting is “disabled”.

The log message is recorded in the switch file system. If the IP address of the

Syslog server has been configured, the switch sends a copy to it.

Size of the Log Message File

The size of the log message file is limited to 4 KB. If the file is full, the oldest

message is replaced.

Figure 111: WBM “System Log” Page

Содержание 852-1305



























































































































































































































































































































Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды

WAGO 852-1305, Руководство пользователя

Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды