WAGO 852-1305 Скачать руководство пользователя страница 278

Страница: 278 / 314

278 Appendix

WAGO-ETHERNET-Zubehör 852

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

10.3.3.16 Loop Detection

Table 138: CLI “Loop Detection” Configuration

Node

Command

Description

enable

show loop-detection

This command displays the current configuration for

“Loop Detection”.

configure

loop-detection (disable |

enable)

This command disables / enables “Loop Detection”

on the switch.

configure

loop-detection address

MACADDR

This command configures the target MAC address

for special “Loop Detection” packets.

configure

no loop-detection address This command resets the target MAC address to the

default setting (00:0b:04:AA:AA:AB).

interface

loop-detection (disable |

enable)

This command disables / enables “Loop Detection”

for a specific port.

interface

no shutdown

This command enables a specific port. It can enable

a port blocked by “Loop Detection”.

interface

loop-detection recovery

(disable | enable)

This command enables / disables the “Recovery”

function on a port.

interface

loop-detection recovery

time VALUE

This command configures the “Recovery Time”

period.

Example

L2SWITCH(config)#

loop-detection enable

L2SWITCH(config)#

interface 1/0/1

L2SWITCH(config-if)#

loop-detection enable

L2SWITCH(config-if)#

loop-detection recovery enable

L2SWITCH(config-if)#

loop-detection recovery time 10

Содержание 852-1305



























































































































































































































































































































Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды

WAGO 852-1305, Руководство пользователя

Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды