WAGO 852-1305 Скачать руководство пользователя страница 113

Страница: 113 / 314

WAGO-ETHERNET-Zubehör 852

Configuration 113

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

Pos: 28.4 /Serie 852 (ETH ERNET-Zubehör)/Konfigurieren/T el net- Por t @ 25\mod_1453208173100_21.docx @ 198621 @ 3 @ 1

8.1.1

Telnet Port

Connect the computer to one of the ETHERNET ports.

Open a Telnet session to the switch’s IP address. If this is your first login,

use the default values.

Table 26: Default Settings for the Telnet Port

Setting

Default Value

FW Version 01

FW Version 02 or

higher

IP Address

192.168.1.254

Subnet Mask

255.255.255.0

Default Gateway

0.0.0.0

Management VLAN

Default Username

admin

Default Password

Wago1951

wago

Make sure your computer IP address is in the same subnet, unless you are

accessing the switch through one or more routers.

Pos: 28.5 /Dokumentation allgemei n/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Содержание 852-1305



























































































































































































































































































































Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды

WAGO 852-1305, Руководство пользователя

Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды