WAGO 852-1305 Скачать руководство пользователя страница 149

Страница: 149 / 314

WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 149

852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX

Manual

1.1.0

9.3.2.1.3 Querier Settings

Figure 47: WBM “IGMP Snooping” Page – “Querier Settings” Tab

Table 51: WBM “IGMP Snooping” Page – “Querier Settings” Tab

Querier Settings
Parameters

Default

Description

Querier State

Disable

Select “Disable” in the selection box to disable this

function.

Enable

Select “Enable” in the selection box to enable this

function.

Querier VLAN State

Add

Select “Add” in the selection box to enter the VLAN

ID.

Delete

Select “Delete” in the selection box to delete the

VLAN ID.

Querier Status
Parameters

Default

Description

Querier State

This field displays the Querier State.

Querier VLAN State

None

0 … 4094

This field displays the VLAN ID.

Содержание 852-1305



























































































































































































































































































































Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды

WAGO 852-1305, Руководство пользователя

Результаты поиска

Содержание 852-1305

Отзывы:

Бренды по названию

Популярные бренды