WAGO 2857-570/024-001 Скачать руководство пользователя страница 71

Страница: 71 / 120

2857-570/024-001

Connection

Product manual | Version: 2.0.0

3-Phase Power Measurement Module, 1 A

8.1 Push-in CAGE CLAMP® Connections

Connect Conductor

Note

Only connect one conductor to each CAGE CLAMP

connection!

Only one conductor may be connected to each CAGE CLAMP

connection. Do not con-

nect more than one conductor on one single connection.

If more than one conductor must be routed to one connection, these must be connected
in an up-circuit wiring assembly, for example, using WAGO Through Terminal Blocks.

Solid, stranded and fine-stranded conductors can be plugged in directly into the Push-in
CAGE CLAMP

. For all other conductor types, the Push-in CAGE CLAMP

and CAGE

CLAMP

must be opened with an operating tool. Only one conductor may be connected

per clamping unit to connect a conductor.

To connect a conductor, proceed as follows:

Figure 29: Opening Push-in CAGE CLAMP

You need an operating tool.

1. Use the operating tool to press and hold the push-button next to the respective con-

nection to open the Push-in CAGE CLAMP

2. Insert the conductor into the corresponding connection opening.

3. Release the push-button to close the Push-in CAGE CLAMP

The conductor is now securely clamped.

Remove Conductor

To remove a conductor, proceed as follows:

Содержание 2857-570/024-001

























































































































Результаты поиска

Содержание 2857-570/024-001

Отзывы:

WAGO 2857-570/024-001, Руководство пользователя, Страница: 71 / 120

Результаты поиска

Содержание 2857-570/024-001

Отзывы: