WAGO 2857-570/024-001 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 120

WAGO 2857-570/024-001 Скачать руководство пользователя страница 17

2857-570/024-001

Properties

Product manual | Version: 2.0.0

17

3-Phase Power Measurement Module, 1 A

Pin assignement for Modbus interface "X1 IN" and "X2 OUT"

Pin contact
(X1; X2)

Assignment

1

N. C.

2

N. C.

3

N. C.

4

A (Data +)

5

B (Data -)

6

N. C.

7

N. C.

8

Common

To form a line structure, two interfaces are internally bridged. See the figure below:

Figure 7: Power Measurement Module on Modbus

3.3.4 Configuration interface "Config"

A WAGO USB Communication Cable (Art.-Nr. 750-923) can be connected here.

To configure the power measurement module for visualizing measured values as the
power is measured and for firmware updates, an engineering PC with the Interface Con-
figuration Software is used.
Communication via the power measurement module and the PC is via the interface “Con-
fig” on the front side. This interface is designed as a 4-pin header used specifically for
WAGO communication solutions.
The operating system recognizes the communication cable as a virtual COM port.

Figure 8: Configuration interface "Config"

3.3.5 Supply Connection "POWER"

An SELV with 24 VDC must be connected at the supply connection “POWER.”
The terminals are the Push-in CAGE CLAMP® design with pushers and have a test slot.

«
...
15
16
17
18
19
...
»

Содержание 2857-570/024-001

























































































































Отзывы:

Нет отзывов