WAGO 2857-570/024-001 Скачать руководство пользователя страница 18

Страница: 18 / 120

2857-570/024-001

Properties

Product manual | Version: 2.0.0
3-Phase Power Measurement Module, 1 A

Figure 9: Power

Position

Designation

Connection

Description

Test slot for
associated
Push-in
CAGE CLAMP

connection

Push-button

Push-button to open the CAGE
CLAMP

GND

Ground

Dig. output, Ground (GND) or S0 in-
terface

24 V

SELV +24 VDC

Power Supply

3.3.6 Memory Card Slot “μSD” for Micro SD Cards

There is a slot for micro SD cards on the front of the power measurement module. A
push/push mechanism locks the memory card in the housing.

Figure 10: Memory card slot

3.3.7 Functional Earth Connection

The functional earth connection is established automatically via the DIN-rail contact when
it is snapped onto the rail.

3.4 Indicators

Table 2: LEDs and Error Indication

LED Display

Explanation

“PWR” LED is illuminated.

Power supply is connected.

“PWR” LED is flashing and
“ERR” LED is illuminated.

4 Hz

Firmware loader enabled/loading/waiting for upload.

“µSD” LED is flashing.

The memory card is being written.

“TxD/RxD” LED is flashing.

Modbus RTU is enabled.

“DO” LED is illuminated.

DO is enabled.

“PWR” LED and “ERR” LED
flash alternately.

Firmware Upload

Содержание 2857-570/024-001

























































































































Результаты поиска

Содержание 2857-570/024-001

Отзывы:

WAGO 2857-570/024-001, Руководство пользователя, Страница: 18 / 120

Результаты поиска

Содержание 2857-570/024-001

Отзывы: