manualshive.com logo in svg

WAGO 2857-570/024-001, Руководство пользователя, Страница: 70 / 120

Поделиться
Скачать
WAGO 2857-570/024-001 Скачать руководство пользователя страница 70

2857-570/024-001

Connection

70

Product manual | Version: 2.0.0
3-Phase Power Measurement Module, 1 A

8

Connection

Protection against dangerous contact voltages

 DANGER

Install protection against electric shock!

All wiring for the measurement system shall be provided with protection against shock
hazard voltages along with the corresponding safety signs!

 DANGER

Always use current measurement transformers or Rogowski coils for current and
power measurements

Current measurement transformers or Rogowski coils corresponding to the requirements
of standard IEC 61869 must always be used for current and power measurements. For
North America (UL) the requirements for current measurement transformers shall be ob-
served, see "Installation Regulations Specified by Approvals."

The transformer or coil are necessary to ensure adequate isolation from the system in
case of electrical fault. Electrical faults can cause shock or burns. Furthermore, current
measurement without a current measurement transformer can lead to a short circuit in the
power network and destruction of the product.

 DANGER

When measuring voltage and power, always observe specifications for measure-
ment topologies, supply networks, voltage levels and voltage measurement trans-
formers

For voltage and power measurement, the product must only be used according to the
specifications for voltage levels and voltage measurement transformers specified for the
respective supply network and measurement topology.

Otherwise, adequate isolation from the system may no longer be possible in the event of
a fault. This can cause electric shock or burns.

Содержание 2857-570/024-001

























































































































Отзывы:

Нет отзывов