manualshive.com logo in svg

WAGO 2857-570/024-001, Руководство пользователя, Страница: 47 / 120

Поделиться
Скачать
WAGO 2857-570/024-001 Скачать руководство пользователя страница 47

2857-570/024-001

Functions

Product manual | Version: 2.0.0

47

3-Phase Power Measurement Module, 1 A

Register 0x0000 – Status word 1

1

Threshold value underrun

Bit 9: Threshold value Overvoltage L3

0

Threshold value not reached

1

Threshold value reached or exceeded

Bit 10: Threshold value Overcurrent L3

0

Threshold value not reached

1

Threshold value reached or exceeded

Bit 11: Tamper Detect

0

Fault Current 

iSUM Lx (t) − iN (t)

 ≤ Tamper Detect Threshold value

1

Fault Current 

iSUM Lx (t) − iN (t)

 > Tamper Detect Threshold value

Bit 12: Rotating Field Indicator

0

Rotating field correct L1–L2–L3 (clockwise)

1

Rotating field incorrect (counterclockwise)

Bit 13: S0 Interface Overclocking Status

0

OK

1

S0 interface is overclocked.

Bit 14, 15: Reserved

4.7.4 Measured Value Register

The higher-level controller has access to a number of measured value registers via Mod-
bus. The measured values for the energies are in the data type INTEGER; all others are
FLOAT. All registers have a size of four bytes (1 DWord). The byte sequence is as fol-
lows:

Table 70: Measured Value Register

Word 1 (high)

Word 2 (low)

Byte 1 (high)

Byte 2 (low)

Byte 3 (high)

Byte 4 (low)

M

S
B

L
S

B

M

S
B

L
S

B

M

S
B

L
S

B

M

S
B

L
S

B

In the table below, all measured variables are listed with the corresponding register ad-
dresses and update intervals.

 Note

The Measured Values are Dependent on the Network Topology!

All measured values are measured only in a 4-wire three-phase networks. In other net-
works, some values are not measured. See table below!

Table 71: Measured Value Register

Register Address

Measured Variable

Measure-
ment Unit 1
A, 5 A / Ro-
gowski

Register Ac-
cess

Update Rate
[ms]

0x0000

Status

none

R

40

0x0002

RMS Current L1

A

R

40

0x0004

RMS Current L2

A

R

40

0x0006

RMS Current L3

A

R

40

Содержание 2857-570/024-001

























































































































Отзывы:

Нет отзывов