VXI Technology VM1548C Скачать руководство пользователя страница 48

Страница: 48 / 106

VXI Technology, Inc.

VM1548C Command Dictionary

ABLE

4-2:

NSTRUMENT

PECIFIC

SCPI

OMMANDS

Command

Description

*RST

Reset Value

FORMat

Sets the output format for digital queries.

ASCII /

(Decimal)

INPut:REGister:POLarity

Sets the active edge of the clock for an input port.

Rising Edge

INPut:REGister:SOURce

Selects the source to clock input data port.

X Disabled

INPut:TTLTrig

Selects 1 of 8 VXI Trigger lines as the input
trigger.

X 0

INPut:TTLTrig:STATE Enable/disable MUX that selects an input trigger.

Disabled

OUTPput:CLOCk:ENABle

Sets the Clock pin to be an output or an input.

Input

OUTPut:CLOCk:POLarity

Sets the active edge of a port’s associated clock.

Rising edge

OUTPut:CLOCk:SOURce

Sets the source of a port’s associated clock.

X NONE

OUTPut:REGister:POLarity

Controls the polarity at which output data is
latched to the specified port.

X Rising

edge

OUTPut:REGister:SOURce

Controls the source of the clock that will latch
output data to the specified port.

X Disabled

OUTPut:TTLTrig

Selects 1 of 8 VXI Trigger lines as the output
trigger.

X 0

OUTPut: TTLTrig:POLarity

Sets the active edge of the TTL trigger.

NORMal

OUTPut: TTLTrig:SOURce

Selects the source for the internal signal
TRIGOUT.

X NONE

OUTPut: TTLTrig:STATE

Enable/disable MUX that selects an output trigger.

Off

READ?

Queries an 8 bit input data port.

N/A

READ? CLOCks

Queries the clock line levels.

N/A

READ? CONTrol

Queries the I/O control line levels.

N/A

READ? ISENse

Queries the drive disable/over-current status level
of each group of six lines.

N/A

RESet:ISENse

Resets drive disable of a group of six lines.

N/A

SOURce:DATA

Sets the value driven by an output port.

X 0

SOURce:DATA:ENABle

Sets an eight bit port for input or output.

X Input

SOURce:DATA:POLarity

Sets the output polarity on an 8-bit port.

X NORMal

STATus:INTerrupt:ENABle

Enables or disables Interrupts to the backplane.

NONE

STATus:INTerrupt:PTRansition

Sets Interrupts to occur on a positive transition.

STATus:INTerrupt:NTRansition

Sets Interrupts to occur on a negative transition.

TRIGger:SEQuence:IMMediate A

word serial event which generates a short pulse.

N/A

Содержание VM1548C











































































































Результаты поиска

Содержание VM1548C

Отзывы:

Бренды по названию

Популярные бренды

VXI Technology VM1548C, Руководство пользователя

Результаты поиска

Содержание VM1548C

Отзывы:

Бренды по названию

Популярные бренды