VXI Technology VM1548C Скачать руководство пользователя страница 23

Страница: 23 / 106

www.vxitech.com

VM1548C Programming

XAMPLES OF

SCPI

OMMANDS

TTLTRIG

IRCUIT

A multiplexer is used to select 1 of 8 different sources as TTLTRIG. The signal is selected using
the following SCPI command:

OUTPut:TTLTrig:SOURce <source>

Where <source> refers to one of
the EXTERNAL CLK lines (CLK0-
5), IMMEDIATE or NONE.

The selected signal is called GLOBAL (TRIGOUT) and after a polarity control, it is called
TTLTRIGGER, which is presented on the VXIbus as the selected TTLTRIG0-7. The specific
TTLTRIG line is selected using the following SCPI command:

OUTPut:TTLTrig <n>

Where <n> refers to one of the 8
TTLTRIG lines.

The TTLTRIGGER is enabled or disabled using the following SCPI command:

OUTPut:TTLTrig:STATe ON

Enables the Trigger

OUTPut:TTLTrig:STATe OFF

Disables the Trigger

The following is an example of how to produce CLK2 as TTLTRIG4 to the backplane:

OUTPut:TTLTrig:STATe ON
OUTPut:TTLTrig:POLarity NORMal
OUTPut:TTLTrig 4
OUTPut:TTLTrig:SOURce EXTERNAL2

If CLK2 is a logic low level, then the following SCPI command would allow a logic high level on
the backplane.

OUTPut:TTLTrig:POLarity INVERT

TTLTRIG 4 will not pull the line
low

Likewise, continuing with this example, the following command would produce a logic low level
on the backplane.

OUTPut:TTLTrig:POLarity NORMal

TTLTRIG 4 will pull the line low

Содержание VM1548C











































































































Результаты поиска

Содержание VM1548C

Отзывы:

Бренды по названию

Популярные бренды

VXI Technology VM1548C, Руководство пользователя

Результаты поиска

Содержание VM1548C

Отзывы:

Бренды по названию

Популярные бренды