manualshive.com logo in svg

VXI Technology VM1548C, Руководство пользователя

Поделиться
Скачать
VXI Technology VM1548C Скачать руководство пользователя страница 18

VXI Technology, Inc. 

18 

VM1548C Preparation for Use 

S

ETTING THE 

L

OGICAL 

A

DDRESS

 

The logical address of the VM1548C is set by a single 8-position DIP switch located near the 
module’s backplane connectors (this is the only switch on the module). The switch is labeled with 
positions 1 through 8 and with an ON position. A switch pushed toward the ON legend will signify 
a logic 1; switches pushed away from the ON legend will signify a logic 0. The switch located at 
position 1 is the least significant bit while the switch located at position 8 is the most significant 
bit. See Figure 2-1 for examples of setting the logical address switch. 
 

SET TO 4

1

ON

2 3 4 5 6 7 8

SET TO 168

1 2 3 4 5 6 7 8

SET TO 8

1

ON

2 3 4 5 6 7 8

SET TO 255

1

ON

ON

2 3 4 5 6 7 8

1

2
3
4
5
6
7
8

Switch

Position

1

2
4
8

16
32
64

128

Switch

Value

ON

ON

(Dynamic)

 

F

IGURE 

2-1:

 

L

OGICAL 

A

DDRESS 

S

WITCH 

S

ETTING 

E

XAMPLES

 

The VMIP may contain three separate instruments and will allocate logical addresses as required 
by the VXIbus specification (revisions 1.3 and 1.4). The logical address of the instrument is set on 
the VMIP carrier. The VMIP logical addresses must be set to an even multiple of 4 

unless dynamic 

addressing is used

. Switch positions 1 and 2 must always be set to the OFF position. Therefore, 

only addresses of 4, 8, 12, 16, ...252 are allowed. The address switch should be set for one of these 
legal addresses and the address for the second instrument (the instrument in the center position) 
will automatically be set to the switch set address plus one; while the third instrument (the 
instrument in the lowest position) will automatically be set to the switch set address plus two. If 
dynamic address configuration is desired, the address switch should be set for a value of 255 (All 
switches set to ON). Upon power-up, the slot 0 resource manager will assign the first available 
logical addresses to each instrument in the VMIP module. 
 
If dynamic address configuration is desired, the address switch should be set for a value of 255. 
Upon power-up, the slot 0 resource manager will assign logical addresses to each instrument in the 
VMIP module. 

Содержание VM1548C











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды