manualshive.com logo in svg

VXI Technology VM1548C, Руководство пользователя

Поделиться
Скачать
VXI Technology VM1548C Скачать руководство пользователя страница 24

VXI Technology, Inc. 

24 

VM1548C Programming 

I

NTERRUPT 

C

IRCUIT

 

This section deals with the interrupt circuit. The VM1548C has the capability to interrupt the slot 
0 controller via the VMIP with either a high going edge or with a low going edge of the IRQ* 
signal. The timing and control circuitry can select one of the six EXTERNAL clocks, GLOBAL 
(TRIGOUT) or NONE as the interrupt trigger. The interrupt is selected and enabled using the 
following SCPI command: 
 

STATus:INTerrupt:ENABle <source>

  

Where <source> is EXTERNAL0-
5, GLOBAL or NONE 

 
The following SCPI command will trigger the status interrupt on a positive edge: 
 

STATus:INTerrupt:PTRansition ON 

 
The following SCPI command will trigger the status interrupt on a negative edge: 
 

STATus:INTerrupt:NTRansition ON 

 
EXAMPLES 
 
To use GLOBAL (TRIGOUT) out as the status interrupt trigger, the following SCPI command 
would be issued: 
 

STATus:INTerrupt:ENABle GLOBAL 

 
To trigger the status interrupt from a negative going edge external clock source from port 3, the 
following SCPI commands would be issued: 
 

STATus:INTerrupt:ENABle EXTERNAL3 
STATus:INTerrupt:NTRansition ON 

 
To trigger the status interrupt from a negative edge going external clock source from port 1, the 
following SCPI commands would be issued: 
 

STATus:INTerrupt:ENABle EXTERNAL1 
STATus:INTerrupt:NTRansition ON 

 

 

Содержание VM1548C











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды