FLASHBAKE
®
/ MICROWAVE OVEN SERVICE PROCEDURES AND ADJUSTMENTS
Form 24694 (April 2001)
Page 29 of 52
SERVICE PROCEDURES AND ADJUSTMENTS
WARNING: DUE TO HIGH VOLTAGE, SPECIAL CARE SHOULD BE TAKEN WHEN MEASURING AROUND
THE MAGNETRON.
WARNING: CERTAIN PROCEDURES IN THIS SECTION REQUIRE ELECTRICAL TEST OR
MEASUREMENTS WHILE THE POWER IS APPLIED TO THE MACHINE. EXERCISE EXTREME CAUTION AT
ALL TIMES. IF TEST POINTS ARE NOT EASILY ACCESSIBLE, DISCONNECT POWER, ATTACH TEST
EQUIPMENT AND REAPPLY POWER TO TEST.
WARNING: HIGH VOLTAGE IS PRESENT, WITH HIGH-CURRENT CAPABILITIES IN THE CIRCUITS OF
THE HIGH VOLTAGE WINDING AND FILAMENT WINDING OF THE HIGH VOLTAGE TRANSFORMER.
WARNING: DO NOT MEASURE THE VOLTAGE IN THE HIGH VOLTAGE CIRCUIT, INCLUDING THE
FILAMENT VOLTAGE OF THE MAGNETRON.
WARNING: NEVER TOUCH ANY CIRCUIT WIRING WITH YOUR HAND OR WITH ANY TOOL DURING
OPERATION.
CAUTION: Remove your wristwatch whenever working close to the magnetron.
CAUTION: High voltage capacitor stays charged for about 30 seconds after the oven is turned off.
CAUTION: Check the ground, do not operate the oven on an extension cord. This oven is designed to
be used when grounded.
CAUTION: Avoid inserting nails, wire, etc. through any holes in the oven during operation.
CAUTION: Personnel should not be exposed to the microwave energy.
DOOR LATCHING ADJUSTMENT
WARNING: DISCONNECT THE ELECTRICAL
POWER TO THE MACHINE AT THE MAIN
CIRCUIT BOX. PLACE A TAG ON THE CIRCUIT
BOX INDICATING THE CIRCUIT IS BEING
SERVICED.
1.
Remove "CONTROL PANEL.”
2.
Close door.
3.
Loosen screws securing switch assembly.
4.
Move switch assembly away from door so door
is completely closed and latched.
5.
Tighten screws securing switch assembly.
6.
Check door operation. Door must latch and be
completely closed. Interlock switches must be
operated when door is closed.
THERMISTOR TEST
WARNING: DISCONNECT THE ELECTRICAL
POWER TO THE MACHINE AT THE MAIN
CIRCUIT BOX. PLACE A TAG ON THE CIRCUIT
BOX INDICATING THE CIRCUIT IS BEING
SERVICED.
1.
Unplug CN6 from control board.
2.
Attach ohm meter leads to thermistor wires.
A.
Reading should be approximately 150K -
220K ohms at room temperature (70
(
F).
NOTE: As the temperature of the thermistor
increases the resistance goes down.
DOOR SWITCHES -
ADJUSTMENT
Individual door switches are not adjustable.
Содержание VFBMW
