Volvo TAD650VE Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 160

background image

Group 30: Electrical system

Diagnostic Trouble Codes

53

Circuit description

The boost temperature sensor consists of a thermistor
which forms a closed circuit with an internal resistor in
the engine control unit (EMS 2), via the engine inter-
face. The thermistor resistor changes in a non-linear
manner, depending on the boost temperature.

The EMS 2 provides the circuit with a reference volt-
age of +5 Volt. The EMS 2 measures the voltage drop
over the thermistor via pin A47 and pin A11 on the
EMS 2. Pin 1 on the sensor is connected to battery
negative via pin A11 on the EMS 2.

When the boost air is cold, the thermistor resistance
is high and the EMS 2 senses a high voltage drop. As
the boost air warms up, the resistance in the ther-
mistor falls and the voltage drop across it falls.

Fault tracing

FMI 0 Boost temperature is too high

Conditions for fault code:

Boost temperature exceeds the set value of the en-
gine protection parameter.

Possible reason:

•

Engine temperature is too high.

•

High surrounding temperature.

•

Dust or dirt on the outside of the intercooler.

•

Faulty boost temperature sensor.

Suitable action:

1.

Check that engine temperature is normal.

2.

Clean the intercooler.

3.

Check function of boost temperature sensor.

splice

Boost air and
temperature

splice

engine
interface

Note! Only TAD 650, 660, 750, 760 has an engine interface. On
TAD 734 the wiring to the EMS 2 is the same but without any en-
gine interface.

«
...
53
54
55
56
57
...
»

Содержание TAD650VE

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TAD650VE

PLUS BLOCK AM45

Бренд: A'OK Страницы: 7

MICROPUMP DEELE

Бренд: Idex Страницы: 23

PRESTIGE PS2.60FA

Бренд: CAB Страницы: 16

WEST EUROTECH 36 T2

Бренд: Weston UK Страницы: 3

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 48

Бренд: Siemens Страницы: 20

Бренд: Siemens Страницы: 26

Бренд: Siemens Страницы: 40

Бренд: Siemens Страницы: 87

Бренд: Siemens Страницы: 96

Бренд: Siemens Страницы: 116

Бренд: Siemens Страницы: 156

Бренд: Siemens Страницы: 252

Бренд: Seg Страницы: 21

Бренд: Lycomin Страницы: 171

Бренд: WÜRGES Страницы: 4

Бренд: Volvo Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды