Volvo TAD650VE Скачать руководство пользователя страница 40

Страница: 40 / 160

Diagnostic Trouble Codes

Group 30: Electrical system

Fault tracing

FMI 1 Fuel pressure is too low

Conditions for fault code:
The fuel pressure alarm depends on the engine revo-
lution.

Suitable action:

Check fuel level.

Open all fuel cocks and check that no leakage
occurs.

Check drive belt adjustment.

Change all fuel filters. (pre- and fine filter)

Check that no fuel hose is squeezed or folded.

Check function of fuel pressure sensor by control
measuring the fuel pressure. (see workshop man-
ual)

Check fuel feed pump.

Change fuel pressure release valve. (see work-
shop manual)

FMI 3 Abnormally high voltage or short
circuit to higher voltage

Conditions for fault code:

The voltage on pin B16 on the EMS 2 is more than
4,75 Volt.

Possible reason:

•

An open circuit in fuel sensor negative cable.

•

Short circuited fuel sensor signal cable to 5V volt-
age or to battery voltage.

•

Faulty sensor.

Suitable action:

Check contact pressure in socket 18 in the engine
connector B. Also check contact pressure in con-
nector at fuel pressure sensor.

Check cable harness and connectors between fuel
sensor and EMS 2.

Check function of fuel pressure sensor.

Содержание TAD650VE

































































































































































Результаты поиска

Содержание TAD650VE

Отзывы:

Volvo TAD650VE, Руководство по ремонту, Страница: 40 / 160

Результаты поиска

Содержание TAD650VE

Отзывы: