Volvo Penta 13L Скачать руководство пользователя страница 41

Страница: 41 / 122

Save/Restore (Save/Restore)

•

Save current configuration

(Save current

configuration). Save the current display settings.

•

Restore last configuration

(Restore last

configuration). Restore the last displayed settings
saved.

•

Restore default configuration

(Restore default

configuration). Restores

all

display setting menus to

factory settings.

NOTICE!

The settings in the following menus do not

normally need to be changed; should a change be
necessary it must be carried out by an authorized
Volvo Penta technician. Refer to the installation
manual for further engine information.

Authorized Volvo Penta dealer or OEM only

•

I/O Status (I/O Status)

•

CAN Termination (CAN Termination)

•

Stop Logic DCU (Stop Logic DCU)

•

Potentiometer supply (Potentiometer supply)

•

Speed Control (Speed Control)

•

Control display unit (Control display unit)

•

Genset/VE (Genset/VE)

•

Buzzer (Buzzer)

•

Information (Information)

Instruments and Controls

47711089 09-2018 © AB VOLVO PENTA

Содержание 13L



























































































































Результаты поиска

Содержание 13L

Отзывы:

Похожие инструкции для 13L

Бренды по названию

Популярные бренды

Volvo Penta 13L, Руководство оператора

Результаты поиска

Содержание 13L

Отзывы:

Похожие инструкции для 13L

Бренды по названию

Популярные бренды