Volvo Penta 13L Скачать руководство пользователя страница 98

Страница: 98 / 122

Erroneus filling of diesel or AdBlue

/DEF

IMPORTANT:

The filling of diesel or AdBlue

/DEF in the wrong tank can result in damage to the engine.

In order to avoid confusion, the AdBlue

/DEF tank has a blue filler cap and a decal affixed to the tank.

Mistaken filling of AdBlue

/DEF in the diesel

tank

Mistaken filling of diesel in the AdBlue

/DEF

tank

• The engine will not run at full power or will not

run at all

• Injectors may be damaged

• Corrosion in the exhaust system between the

turbocharger and aftertreatment system

• Expensive repairs

• The aftertreatment system may be seriously

damaged

• The engine will no longer fulfill emission level

requirements

• Expensive repairs

Maintenance

47711089 09-2018 © AB VOLVO PENTA

Содержание 13L



























































































































Результаты поиска

Содержание 13L

Отзывы:

Похожие инструкции для 13L

Бренды по названию

Популярные бренды

Volvo Penta 13L, Руководство оператора

Результаты поиска

Содержание 13L

Отзывы:

Похожие инструкции для 13L

Бренды по названию

Популярные бренды